例文 (8件) |
"effective tension"を含む例文一覧と使い方
該当件数 : 8件
A CPU 15 detects effective tension Te and a rotating speed (n) when measuring its effective tension Te while the driving pulley 10 rotates in the measuring rotating speed area.例文帳に追加
CPU15は、原動プーリ10が測定回転数域で回転する間に、有効張力Teと、その有効張力Teが測定されたときの回転数nを検出する。 - 特許庁
In the processing, the ECU 100 obtains by a strain sensor 221 a strain in a crank pulley 220 rotating integrally with a crankshaft 219, which is caused in response to changes in effective tension Te of the timing belt 222, and obtains a peak value Tep of the effective tension.例文帳に追加
係る処理において、ECU100は、クランクシャフト219と一体に回転するクランクプーリ220にタイミングベルト222の有効張力Teの変化に応じて発生する歪みの量を歪みセンサ221から取得し、係る有効張力のピーク値Tepを取得する。 - 特許庁
The PU 15 determines whether or not its effective tension Te is within an allowable range Te_r determined with every rotating speed in its rotating speed (n).例文帳に追加
CPU15は、その有効張力Teがその回転数nにおいて、回転数毎に定められた許容範囲Te_r内かどうかを判定する。 - 特許庁
CPU15 detects a maximum Te_max of an effective tension Te and a rotational speed n_max at the maximum tension when the rotational speed is increasing after the driving pulley 10 starts its rotation.例文帳に追加
CPU15は、原動プーリ10が回転を開始した後、回転数が上昇しているとき、有効張力Teの最大値Te_maxと、その最大値における回転数n_maxを検出する。 - 特許庁
If the peak value Tep of the effective tension is greater than a prescribed threshold Tepth, the ECU 100 controls an intake-side VVT controller 300 and an exhaust-side VVT controller 400 to increase the overlap of an intake valve 203 and an exhaust valve 206, and decrease the peak value Tep of the effective tension acted on the timing belt 222.例文帳に追加
ECU100は、この有効張力のピーク値Tepが、予め設定された閾値Tepthよりも大きい場合に、吸気側VVTコントローラ300及び排気側VVTコントローラ400を夫々制御し、吸気バルブ203及び排気バルブ206のバルブオーバラップ量を増加せしめ、タイミングベルト222に作用する有効張力のピーク値Tepを低減させる。 - 特許庁
Then, the driven pulley 40 is locked for preventing rotation, a motor 10 is rotated, tension T2 at a slack side at this time and effective tension FP are measured by the load cell 4 and a torque-measuring instrument 5, respectively, and the Euler formula is used for calculating a friction coefficient.例文帳に追加
次に従動プーリ40を回転不能にロックし、モーター10を回転させ、この時の緩み側張力T2をロードセル4で、有効張力FPをトルク測定器5で測定し、オイラーの公式を用いて摩擦係数を算出する。 - 特許庁
When a thrust load is applied to the radial ball bearing 13 via an adjusting screw 15, rotation resistance is generated depending on the thrust load, and takeup tension of the wire 16 caused by the spiral spring 14 is compensated for, whereby effective tension of the wire 16 is set at an arbitrary value.例文帳に追加
調節ねじ15を介してラジアルボールベアリング13にスラスト荷重を与えると、スラスト荷重に応じて回転抵抗が発生し、うず巻ばね14によるワイヤ16の巻取り張力を相殺してワイヤ16の有効張力を任意に設定することができる。 - 特許庁
Based on the belt winding lengths L_DR, and LD_N of the drive pulley and the driven pulley, the WD coefficients as pressing forces against the pulleys per belt unit length are obtained, ST coefficients as the effective tension of the belt per unit winding length are obtained, and based on the relational expression of the WD coefficients to the ST coefficients, the tensioner device 11 is controlled.例文帳に追加
ベルト単位長さ当たりのプーリへの押付力であるWD係数を駆動プーリおよび従動プーリのベルト巻き掛け長さL_DR,L_DNに基づいて求めるとともに、単位巻き付き長さ当たりのベルトの有効張力であるST係数を求め、WD係数とST係数との関係式に基づいてテンショナ装置11を制御する。 - 特許庁
例文 (8件) |
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|