例文 (116件) |
K value controlの部分一致の例文一覧と使い方
該当件数 : 116件
The preliminary control value (V) is multiplied as mentioned below by a correction value (K).例文帳に追加
この予備制御値(V)は、以下で補正値(K)と乗算される。 - 特許庁
The value V is multiplied by a control gain K in order to calculate a control target value C by a control target value calculation part 10.例文帳に追加
この値Vに制御目標値算出部10によって制御ゲインKが乗算されて制御目標値Cが求まる。 - 特許庁
A switching function σ of sliding mode control is set as a linear function of deviation e(k) between deviation quantity DTH of an aperture of a throttle valve and a target value DTHR of the deviation quantity of the aperture of the throttle valve (σ(k)=e(k)+VPOLE.e(k-1)).例文帳に追加
スライディングモード制御の切換関数σを、スロットル弁開度偏差量DTHと、スロットル弁開度偏差量の目標値DTHRとの偏差e(k)の線形関数として設定する(σ(k)=e(k)+VPOLE・e(k-1))。 - 特許庁
In steps S26, S27, a control signal P is outputted to an AND circuit 14, and in step S28 it is judged whether or not a measured current value A (K) falls within a range between the first reference current value X (K) and the second reference current value Y (K).例文帳に追加
ステップS26,S27にてAND回路14に制御信号Pを出力すると共に、測定電流値A(K) が第1基準電流値X(K) と第2基準電流値Y(K) との範囲内にあるか否かが判断される(ステップS28)。 - 特許庁
If the radius of curvature 1/R is at a fixed value A or more (S9), a control gain K is set from a control gain map (S10).例文帳に追加
ステップS9で曲率1/Rが所定値A以上ならば、ステップS10で制御ゲインマップから制御ゲインKを設定する。 - 特許庁
A control unit for internal combustion engine calculates electric power consumption WAFM of heat wire from output voltage VAFM of an air flow sensor 11 (S13), and calculates this time value WAMFH(k) of delay compensation electric power using this time value WAFM (k) and the preceding value WAFM(k-1) of electric power consumption (S15).例文帳に追加
エアフローセンサ11の出力電圧VAFMから熱線の消費電力WAFMを算出し(S13)、消費電力の今回値WAFM(k)及び前回値WAFM(k-1)を用いて、遅れ補償電力の今回値WAMFH(k)を算出する(S15)。 - 特許庁
A lamp control circuit 201 outputs a control signal P, based on the average value K of the luminance.例文帳に追加
ランプ制御回路201は、その輝度の平均値Kに基づいて、制御信号Pを出力する。 - 特許庁
The voltage V_C of C_1 or C_2 is monitored at all times and the command value of the ratio K is obtained by PI control or PID control from a difference ΔV from a desired value V_C0, and a command value of the duty factor D_st is computed from the command value of the ratio K.例文帳に追加
この後、C_1又はC_2の電圧V_Cを常時監視して目標値V_C0との差ΔVから比Kの指令値をPI制御又はPID制御により求め、ここからデューティー比D_stの指令値を算出する。 - 特許庁
A control value output circuit 102 calculates a delay control value 104 corresponding to a delay amount of K/N of a unit delay amount per cycle of the input clock signal based upon the delay indicated value K.例文帳に追加
制御値出力回路102により、遅延指示値Kに基づいて入力クロック信号の1サイクル当たりの単位遅延量のK/Nの遅延量に対応する遅延制御値104を算出する。 - 特許庁
Such fuel addition control is strongly executed as the correction value K stored in the RAM is larger, and is weakly executed as the correction value K is smaller.例文帳に追加
こうした燃料添加制御に関しては、RAMに記憶された補正値Kが大きいほど強く行われるとともに、同補正値Kが小さいほど弱く行われる。 - 特許庁
Here, the coefficient Ksub is determined based on the downstream side feedback correction value Vafsfb(k) such that the control basic fuel injection amount Fbasec (accordingly, fuel injection amount Fi) is determined such that the output value Vabyfs of the upstream side air/fuel ratio sensor 66 is varied in a direction for denying variation of the downstream side feedback correction value Vafsfb(k).例文帳に追加
ここで、係数Ksubは、上流側空燃比センサ66の出力値Vabyfsが下流側フィードバック補正値Vafsfb(k)の変化を打ち消す方向に変化するように制御用基本燃料噴射量Fbasec(従って、燃料噴射量Fi)が決定されるよう、下流側フィードバック補正値Vafsfb(k)に基づいて決定される。 - 特許庁
A 4-6 modulation part 12 displays two information word candidates C(k)a and C(k)b to an input data word D(k) if necessary, and outputs the information word string of (1, 7) RLL rules subjected to DSV control by selecting an information word to set a small DSV absolute value.例文帳に追加
4−6変調部12では、入力データ語D(k)に対し必要に応じて2つの情報語候補C(k)a,C(k)bを示し、DSVの絶対値を小さくする方の情報語の選択によってDSV制御を施した(1,7)RLL規則の情報語列を出力する。 - 特許庁
A control part 10 arranges the intervals K of prescribed number of established image sheets to the maximum value of a counter 10A.例文帳に追加
制御部10は、設定された画像の枚数間隔Kをカウンタ10Aの最大値に設定する。 - 特許庁
A feedback control signal S is set at (K-G×x^2)×dx/dt (wherein x is the oscillation displacement of the cantilever 10, dx/dt is the oscillation speed of the cantilever 10, and both of K and G are a feedback gain of a positive value).例文帳に追加
ただし、xはカンチレバー10の振動変位、dx/dtはカンチレバー10の振動速度、K、Gはともに正値のフィードバックゲインである。 - 特許庁
A control signal generation means 30 uses a contour detection signal from a contour detection filter 10 and a standard deviation from a means detecting variations 20 to calculate an image quality control value k and supplies a control signal including the image quality control value k to a first control part 60 and a second control part 70.例文帳に追加
制御信号生成手段30は、輪郭検出フィルタ10からの輪郭検出信号と、ばらつき量検出手段20からの標準偏差とを用いて画質制御値kを算出し、この画質制御値kを含めた制御信号を、第1制御部60及び第2制御部70に供給する。 - 特許庁
In the temperature rise control, the learning value K is calculated as the value corresponding to the steady difference between a catalyst bed temperature average value Tave and the target bed temperature Tt.例文帳に追加
昇温制御中においては、学習値Kが触媒床温平均値Taveと目標床温Ttとの定常的なずれに対応する値として算出される。 - 特許庁
The sub-feedback control constant K is compensated based on an actual measurement value of an estimated value of the element temperature T of the second air-fuel ratio sensor 53.例文帳に追加
また、第二空燃比センサ53の素子温度Tの実測値あるいは推定値に基づいてサブフィードバック制御定数Kが補正される。 - 特許庁
The command value of the duty factor D_st can be obtained more accurately by conducting PI control or PID control at the ratio K than in direct acquirement by PI control or PID control of the command value of the duty factor D_st.例文帳に追加
デューティー比D_stの指令値を直接PI制御又はPID制御により求めるよりも、比KでPI制御又はPID制御を行うことで、デューティー比D_stの指令値を的確に求めることができる。 - 特許庁
When the control voltage and the gain are denoted by V and k, respectively, the value of Vc×k is constant, independently of whether the oscillation in the oscillation loop is in a steady-state or in a start-up process.例文帳に追加
制御電圧をVc、ゲインをkとした場合に、発振ループ内の発振が定常状態か起動過程かにかかわらず、Vc×kの値が一定である。 - 特許庁
The control signal CNT is generated based on a counter value K, which is obtained from the clock generating circuit 1, in the power source control means 31.例文帳に追加
制御信号CNTは、電源制御手段31において、クロック生成回路1から得られるカウンタ値Kに基づいて生成される。 - 特許庁
Further, the value of the affection parameter Sk (k) of the new character, which affects the value of the capacity parameter Np (j, m) of the character, is recognized by the control part 1.例文帳に追加
そして、キャラクタの能力パラメータNp(j,m)の値に影響を与える、新規キャラクタの影響パラメータSk(k)の値が、制御部1に認識される。 - 特許庁
The control device extracts information on the gain K from the integration value and stores a deviation from an original gain assumed by the control device 40 as a gain correction value in a nonvolatile memory 42.例文帳に追加
そして、積算値からゲインKの情報を抽出し、制御装置40の想定している本来のゲインとのずれ量をゲイン補正量として不揮発性メモリ42に記憶する。 - 特許庁
The control part 109, when the sensitivity setting value signal is input, reads out a correction coefficient K stored in a memory part 112, and calculates a sensitivity application value by multiplying the sensitivity setting value by the correction coefficient K, and outputs a control signal of an electron multiplication rate according to the sensitivity application value to a CCD driving part 108.例文帳に追加
制御部109は感度設定値信号が入力されると、メモリ部112に記憶された補正係数Kを読み出し、感度設定値に補正係数Kを乗算して感度適用値を算出し、感度適用値に応じた電子増倍率の制御信号をCCD駆動部108に出力する。 - 特許庁
A coefficient K is assumed as K=1 when generation of idling slide is not detected in other shafts, and when detected, it is assumed as the value computed in a K calculation part 51, during a control parameter value changing period Pp after being detected until time Tp passes.例文帳に追加
係数Kは、他軸において空転滑走の発生が検知されていない場合にはK=1とされ、検知された場合には、検知されてから時間Tpが経過するまでの制御パラメータ値変更期間Ppの間、K算出部51で算出された値とされる。 - 特許庁
A correction unit 44 corrects control variables (the limit value VL of a speed limiter 50 and the limit value GL of an acceleration limiter 52, and the gain K in a drive control unit 40) to the correction value corresponding to the responsive waveform of the angle of inclination.例文帳に追加
修正部44は、制御変数(駆動制御部40内の速度リミッタ50のリミット値VL、加速度リミッタ52のリミット値GL、ゲインK)を、傾斜角の応答波形に対応した修正値に修正する。 - 特許庁
The displacement feedback control unit 37a controls to decrease an apparent spring constant K' represented by a difference between the spring constant K of the air spring 21 and a value proportional to the control gain G, by adjusting the control gain G.例文帳に追加
変位フィードバック制御部37aは、制御ゲインGを調整することにより、空気ばね21のばね定数Kと制御ゲインGに比例する値との差で表される見かけのばね定数K’を小さくするような制御を行う。 - 特許庁
Furthermore, the control device (8') includes a storage means (12) for forming a value of the control signal (9') at a time k-1, and an addition means (10) for adding an output signal Y of the quantizer and the stored value of the first control signal (9') at the time k-1.例文帳に追加
また、制御装置(8´)は、制御信号(9´)の値を時間k−1において形成するための格納手段(12)、および、量子化器の出力信号Yと、時間k−1において第1制御信号(9´)の格納値とを加算するための加算手段(10)を含んでいる。 - 特許庁
A control judging function 13 of a master device 1 judges the difference between a standard received electric field value k and a power value detected by a received electric field detection function 11, and requests a transmitted power control when the difference exceeds a control allowable value.例文帳に追加
親装置1の制御判定機能13は標準受信電界値kと受信電界検出機能11で検出した受信電力値との差を判定し、その差が制御許容値を越えた時に送信電力制御を要求する。 - 特許庁
An off-assist voltage command value generation circuit 17 inputs the voltage value Vs of a system voltage signal 24 in a power system 1 detected by a voltage detector 9, the maximum voltage value Vmax which can be outputted by a voltage converter 7, and an off-assist control factor k (k is a real number, where 0<k<1).例文帳に追加
オフアシスト電圧指令値生成回路17は、電圧検出器9にて検出した電力系統1の系統電圧信号24の電圧値Vsと、電力変換器7の出力可能な最大電圧値Vmaxと、オフアシスト制御係数k(kは実数で、0<k<1)とを入力する。 - 特許庁
When an anti-lock brake control and a brake assisting control are simultaneously performed, if a brake fluid pressure value P after a brake fluid pressure is increased by the brake assisting control and increased or decreased by the anti-lock brake control is smaller than a prescribed set value K, the brake fluid pressure value is corrected to a higher one.例文帳に追加
アンチロックブレーキ制御及びブレーキアシスト制御が同時に行われる際、ブレーキアシスト制御によりブレーキ液圧を増圧しアンチロックブレーキ制御により増減圧した後のブレーキ液圧値Pが所定の設定値Kより小さいときには、ブレーキ液圧値を増加補正する。 - 特許庁
The detection control unit 20 calculates, for each setting value of the sub PP gain k, a degree of influence of the shifting voltage of the objective lens 10 on a DPP balance value BL.例文帳に追加
そうすると、検出制御部20は、サブPPゲインkの設定値毎に、対物レンズ10のシフト電圧のDPPバランス値BLに対する影響度を求める。 - 特許庁
When the LSB of a shift register value memorized in a temporary register R is not 0 (S5;No), the coordinate value equivalent to a counter value in a counter C before a control cycle is memorized in a temporary register K (S6).例文帳に追加
テンポラリレジスタRに記憶しているシフトレジスタ値のLSBが0でない場合は(S5;No)、カウンタCのカウンタ値分の制御周期前における座標値をテンポラリレジスタKに記憶する(S6)。 - 特許庁
Then, the calculated rotational frequency compensating coefficient k is outputted to the fan drive control unit corresponding to the normal cooling fan and rotational frequency target value is varied by the rotational frequency compensating coefficient k by the fan drive control unit adjusted by the rotational frequency compensating coefficient k.例文帳に追加
そして、協調制御部58は、その算出した回転数補正係数kを正常な冷却ファンに対応するファン駆動制御部へ出力し、回転数補正係数kを受けたファン駆動制御部は、回転数補正係数kによって回転数目標値を変更する。 - 特許庁
A control part 18 reads the fixed time Tm+k and the setup value Gm+k+1 stored in the memory 17, and sets the setup value Gm+k+1 to the optical functional device 15 after the lapse of the fixed time Tm+k after the reception of the optical signals transmitted from the m+kth ONU 12 is started in an up signal receiving unit 16.例文帳に追加
制御部18は、記憶部17に記憶された一定時間Tm+k及び設定値Gm+k+1を読み込み、第m+k番目のONU12から送信された光信号を上り信号受信部16で受信し始めてから一定時間Tm+kの経過後に、設定値Gm+k+1を光機能デバイス15に設定する。 - 特許庁
From an analysis result, an optimal reset time Ro is considered as Ro=4*|K|*(T+L) by a proportionality control object signal transmission characteristic value from the operation amount to a control amount, namely, a gain constant K and a delay time (equivalent time constant T + equivalent dead time L).例文帳に追加
解析結果から、操作量から制御量までの定位性制御対象信号伝達特性値、すなわちゲイン定数Kと遅れ時間(等価時定数T+等価むだ時間L)とより、最適リセット時間RoをRo=4*|K|*(T+L)とする。 - 特許庁
A transfer bias supplied to a divided region that the width-directional end of the transfer material is opposed to among a plurality of divided regions of a transfer roller 7 is brought under constant-current control to a control current value Ix satisfying equation (1) Ix=I×k+IO×(t-k).例文帳に追加
転写ローラ7の複数の分割領域のうち、転写材の幅方向端部が対向する分割領域に供給される転写バイアスは、次の(1)式を満たす制御電流値Ixに定電流制御される。 - 特許庁
A delay indicated value calculating circuit 101 obtains a delay indicated value which is obtained by cumulatively adding M-N in every cycle of the input clock signal and generated by subtracting N from K when the delay indicated value K exceeds N, and increases or decreases the delay indicated value K according to a phase adjustment signal 30 showing phase control over the output clock signal.例文帳に追加
遅延指示値算出回路101により、入力クロック信号のサイクルごとにM−Nを累積的に加算した値からなる遅延指示値Kであって、かつ遅延指示値KがN以上となった場合にはKからNを減算した値となる遅延指示値Kを求め、出力クロック信号に対する位相制御を示す位相調整信号30に応じて遅延指示値Kの値を増減する。 - 特許庁
The detection control unit 20 detects, based on an approximate equation indicating a relationship between the degree of influence and the sub PP gain k, a value of the sub PP gain k when the degree of influence is lowest as an optimum servo parameter.例文帳に追加
さらに、上記影響度とサブPPゲインkとの関係を表す近似式に基づいて、上記影響度が最小となるときのサブPPゲインkの値を最適サーボパラメータとして検出する。 - 特許庁
That is, the number of revolution is controlled by k times of number of revolution R corresponding to the specified value f0 in a motor revolution number control part 30, and the frequency of the wobble signal is detected by k times of specified value f0 in a wobble signal detector 4.例文帳に追加
すなわち、モータ回転数制御部30での回転数の制御を規定値f0に対応した回転数Rのk倍で行い、ウォブル信号検出器4において、規定値f0のk倍でウォブル信号の周波数を検出する。 - 特許庁
The control part 107 performs correction based on a DC value which is estimated according to all data included in a K space to which each data belongs.例文帳に追加
制御部107は、この補正を、各データが属するK空間に含まれる全てのデータに基づいて推定したDC値に基づいて行う。 - 特許庁
By a reproduction control circuit 14, the size of the detecting window is controlled so that the resolution from the resolution detecting part 15 is approached to a reference value K from a reference value output circuit 13.例文帳に追加
再生制御回路14は、解像度検出部15からの解像度が基準値出力回路13からの基準値Kに近づくように検出窓の大きさを制御する。 - 特許庁
The motor control signal output section 44 includes an F/B gain calculation part 61 which changes a value of the F/B gain K into low response value when a vehicle is in a straight moving state.例文帳に追加
そして、モータ制御信号出力部44に、車両が直進状態である場合にF/BゲインKの値を低応答値に変更するF/Bゲイン演算部61を設けた。 - 特許庁
The second control part 70 adds a signal resulting from multiplying an input image signal by the image quality control value k and a signal resulting from multiplying the output signal from the first control part 60 by 1-k and outputs the addition result as an output signal of a noise reduction device 100.例文帳に追加
第2制御部70は、入力画像信号に対して画質制御値kを乗算した信号と、第1制御部60からの出力信号に対して「1−k」を乗算した信号とを加算して、ノイズリダクション装置100の出力信号として出力する。 - 特許庁
The sum of differences is normalized to control sensitivity to motion in the image to obtain a value of a proportional parameter K(x, y) for each pixel.例文帳に追加
この差の合計は、各画素についての割合パラメータK(x,y)の値を得るために、イメージ内の動きに対する感度を制御するために正規化される。 - 特許庁
A low order bit control unit 330 performs a frequency-dividing operation, and selects a low-order current source cell 533 of a weighted current value by using a (1/2)^k frequency-division clock.例文帳に追加
下位ビット制御部330は、分周動作を行ない1/2^k分周クロックを使用して重付け電流値の下位電流源セル533を選択する。 - 特許庁
By comparing the degree K of the thermal degradation with an abnormality determination value S, it is determined whether the exhaust emission control catalyst is thermally degraded or not (steps 130, 140).例文帳に追加
この熱劣化度Kと異常判定値Sとを比較することで、排気浄化触媒が熱劣化異常であるかどうかを判定する(ステップ130,140)。 - 特許庁
The control unit 107 performs the correction based on the DC value estimated based on the data included in the whole range of K-space to which each data belongs.例文帳に追加
制御部107は、この補正を、各データが属するK空間の全範囲に含まれるデータに基づいて推定したDC値に基づいて行う。 - 特許庁
When the count of the counter section 13 is increased more than a preset fixed value K, a control section 14 controls execution of the control channel retrieval in the mobile set 1.例文帳に追加
制御部14はカウンタ部13のカウンタ値が予め設定されたある固定値Kより大きくなると、移動機1における制御チャネル検索動作を実行するよう制御する。 - 特許庁
The capability operation amount is not suddenly increased, but increased by stages by providing a control threshold K as shown in Fig.5(b), so that the supercooling degree ΔTs is always kept to a value larger than the threshold K.例文帳に追加
能力操作量を急激に増加するのではなく、図5(b)に示すように制御閾値Kを設けて、過冷却度ΔTsが閾値Kより常に大きい値に維持されるように、段階的に増加していく。 - 特許庁
例文 (116件) |
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|