意味 | 例文 (79件) |
dimension toleranceとは 意味・読み方・使い方
追加できません
(登録数上限)
「dimension tolerance」の部分一致の例文検索結果
該当件数 : 79件
The second crossing dimension is within the ISO H7 standard tolerance.例文帳に追加
第2の横断寸法はISO H7標準公差以内である。 - 特許庁
A dimension/tolerance addition part decides a dimension vector to a dimension between a line or a point, and the origin, confirms whether or not a direction of the edge tolerance vector of the line or the point tolerance vector of the point, and a direction of the dimension vector accord, and determines a sign of the tolerance.例文帳に追加
寸法・公差付加部は、線または点と原点との寸法に対して寸法ベクトルを定め、当該線のエッジ公差ベクトルまたは当該点のポイント公差ベクトルの方向と寸法ベクトルと方向が一致する否かを確認して公差の符号を決定する。 - 特許庁
A dimension condition setting part 22 defines the dimension tolerance of design data and each component.例文帳に追加
設計データ及び各構成部品の寸法公差を寸法条件設定部22によって定義する。 - 特許庁
A primary analysis executing part 13 uses the dimension tolerance defined by the dimension tolerance setting part 22 to execute a primary analysis and calculates distribution and deviation.例文帳に追加
一次解析実行部13寸法公差設定部22によって定義された寸法公差を用いて一次解析を実行して、分散または偏差を求める。 - 特許庁
Diameter dimension of the gauge 50 can be defined as (hole-diameter of the pin hole-deviation tolerance).例文帳に追加
ゲージ50の径寸法は、(ピン孔の孔径−ズレ公差)とすることができる。 - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解! -
「dimension tolerance」の部分一致の例文検索結果
該当件数 : 79件
A pipe material 3 whose overall length exceeds a tolerance dimension is attached in a recessed part 5 of a lower die 4.例文帳に追加
全長が許容寸法を超えているパイプ素材3をロアダイ4の凹部5内に仕掛ける。 - 特許庁
The inner diameter dimension 62 of the casing 11 is set to 26.5 mm with its upper limit tolerance 0 mm and with its lower limit tolerance 0.04 mm.例文帳に追加
ケーシング11の内径寸法62を、26.5mmで上限の公差が0mm、下限の公差が0.04mmとなるように設定する。 - 特許庁
A self-aligning gap δ is provided around a shaft of the oscillating member and the relation of "dimension tolerance of L + dimension tolerance of M≤δ≤0.2 mm" is set up in case that its gap is as δ, the claw dimension of the drive claw 22 is represented by L and the assembly dimension of the drive claw 22 is represented by M.例文帳に追加
揺動部材の回転軸周りに自動調芯すき間δを設け、そのすき間δを、駆動爪22の爪寸法L、駆動爪偉22の組付け寸法Mとした場合に、「Lの寸法公差+Mの寸法公差≦δ≦0.2mm」の関係を有するように設定した。 - 特許庁
The outside diameter dimension 61 of the ring 21a is set to 26.5 mm with its upper limit tolerance -0.045 mm and with its lower limit tolerance -0.090 mm.例文帳に追加
リング部21aの外径寸法61を、26.5mmで上限の公差が−0.045mm、下限の公差が−0.090mmとなるように設定する。 - 特許庁
To easily abut a light emission surface of an LED on a light guide plate irrespective of dimension tolerance of the LED.例文帳に追加
LEDの寸法公差に関係なく、LEDの発光面を容易に導光板に当接させる。 - 特許庁
To enhance a holding force for a pipe P1, without making a tolerance dimension severe, in a pipe holder 10.例文帳に追加
パイプ保持具10は、公差寸法を厳しくしなくても、パイプP1に対する保持力を高めたこと。 - 特許庁
In this way, the product of the dimensional tolerance of ±0.05 mm below in the final cross sectional dimension is obtained.例文帳に追加
これにより、最終断面寸法における寸法公差が±0.05mm未満の製品が得られる。 - 特許庁
Thus, since a dimension being a reference of an ordinary allowance, that is, an inside diametrical dimension D1 of the lip seal 50 becomes larger than an inside diametrical dimension of the lip seal 50 in a conventional pump, a tolerance also expands according to the expansion of a reference dimension.例文帳に追加
これにより、普通許容差の基準となる寸法、つまりリップシール50の内径寸法D1が従来型ポンプにおけるリップシール50の内径寸法より大きくなるので、公差も基準寸法の拡大に応じて拡大する。 - 特許庁
|
意味 | 例文 (79件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると
|
「dimension tolerance」のお隣キーワード |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると
|