意味 | 例文 (999件) |
TARGET VALUEの部分一致の例文一覧と使い方
該当件数 : 7972件
The optical range finder obtains a ratio (multiplication) Mx of an output Vo of the photodetector for the light emission monitor (PD) 9 to an output Vx of the ranging photodetector (APD) 4 and corrects a bias voltage of the ranging photodetector (APD) 4 so that the ratio (multiplication) Mx is near to a target value M.例文帳に追加
そして、発光モニタ用光検出器(PD)9の出力Voと測距用光検出器(APD)4の出力Vxとの比(増倍率)Mxを求め、前記比(増倍率)Mxが目標値Mに近づくように、測距用光検出器(APD)4のバイアス電圧を補正する。 - 特許庁
An image high resolution processing method by a point-based projection filter method obtains a coefficient vector a^(x(H), y(H)) in advance by each position (x^(H), y^(H)) of a target pixel in a regional size and obtains a pixel value by acting this coefficient vector to each pixel of a restoration image f_0 to generate the restoration image.例文帳に追加
各点射影フィルタ法による画像の高解像度化では、領域サイズにおける着目画素の位置(x^(H),y^(H))毎に予め係数ベクトルa^(x(H),y(H))を求めておき、復元画像f_0の画素毎にこの係数ベクトルを作用させて画素値を求めることにより、復元画像を生成する。 - 特許庁
The target temperature value of the strip S at each outlet side in plural zones 31 and 32 is set so that the fuel flow distribution in each of plural zones 31 and 32 in the heating zone 3 becomes a prescribed pattern, to put it concretely, the fuel flow distribution in each of the zones 31 and 32 is substantially equalized.例文帳に追加
加熱帯3の複数のゾーン3_1 、3_2 の各々における燃料流量分布が所定のパターン、具体的には各ゾーン3_1 、3_2 における燃料流量分布が実質的に均一となるように、複数のゾーン3_1 、3_2 の各々の出側におけるストリップSの目標板温値を設定する。 - 特許庁
When a target message to be sent out is newly sent out (S12: YES), a control unit of the in-vehicle communication device sets a numeral that the high-order bit sequence of an arbitration field of the message to be sent out to a predetermined value (S13), and then starts sending it out (S14).例文帳に追加
車載通信装置の制御部は、送出を試みようとするメッセージについて新たな送出である場合は(S12:YES)、送出を試みるメッセージのアービトレーションフィールドの上位ビット列が表す数値を所定値に設定し(S13)、送出を開始する(S14)。 - 特許庁
Since the reaction torque is large when the rotation position of the control shaft is in a range of θ2 - θ3, if a target rotation position (solid line) is kept at a constant value in the range for a predetermined period of time (T seconds), a mode is shifted to "undulation mode" and the actuator is forcedly reciprocated at minute amplitude.例文帳に追加
制御軸の回転位置がθ2〜θ3の範囲では、反力トルクが大であるので、その範囲内で、目標回転位置(実線)が所定期間(T秒間)一定値に維持されたら、”うねりモード”に移行し、微小振幅でもって、強制的にアクチュエータを往復動させる。 - 特許庁
To dispense with the selection of a pair of frequencies of the beat signal frequencies of an up phase and a down phase, and to improve a measurement precision of the relative distance and relative speed of an external target by using the observation value of the beat signal frequency of both the phases in a radar system according to an FMCW radar method.例文帳に追加
FMCWレーダ方式によるレーダ装置において、アップフェーズとダウンフェーズのビート信号周波数の周波数対を選択する必要がなく、かつ両フェーズのビート信号周波数の観測値を用いて外部目標の相対距離と相対速度との計測精度の向上を図る。 - 特許庁
When a stop instruction signal such as an OFF signal of an ignition switch and abnormality information by the failure diagnosis is detected, the drive of an assist motor 6 is stopped if the absolute value of the target current Im* is not more than the determination current Im0, or if the predetermined time is elapsed.例文帳に追加
イグニッションスイッチのオフ信号及び故障診断による異常情報などの停止指示信号を検出したときには、目標電流Im*の絶対値が判定電流Im0以下の場合、若しくは、所定時間を経過した場合に、アシスト電動機6の駆動を停止させる。 - 特許庁
To provide a heat treatment method, and a device thereof in which the uniform tempering over the thickness direction, softening, etc., of only a surface layer of a steel, and temper-softing in the thickness direction of the steel can be performed while the productivity is not impaired and the surface temperature of the steel plate does not exceed the target value.例文帳に追加
生産性を阻害せず、しかも鋼板の表面温度が目標温度を超えることなく厚み方向にわたって均一な焼戻し処理、および、鋼材表層のみの軟化等、鋼材板厚方向での焼き分けを行うことが可能な熱処理方法およびその装置を提供する。 - 特許庁
When sliding down reduction control is performed by controlling a liquid pressure of a brake actuator, a vehicle body acceleration α is estimated (S220), and a control target pressure P is increased and compensated (S224) if the vehicle body acceleration α is larger than a predetermined value ('YES' at S222) to generate a larger braking force.例文帳に追加
ブレーキアクチュエータの液圧制御を行って、ずり落ち緩和制御を実施する際に、車体加速度αを推定し(S220)、車体加速度αが所定値より大の場合には(S222で「Yes」)、制御目標圧Pを増加補正して(S224)、より大きな制動力を発生させる。 - 特許庁
An ECU 30 cools a motor device (the motor 26 and motor drive circuit 31) when stop or almost stop of the change of the rotational phase (locked state) during the changing of the rotational phase of the camshaft 16 to a target value is detected after the engine 11 is at a stop.例文帳に追加
ECU30は、エンジン11の停止後において、カム軸16の回転位相の目標値への変化中に回転位相の変化が停止又はほぼ停止した状態(ロック状態)が発生したことを検出した場合、モータ装置(モータ26、モータ駆動回路31)を冷却する。 - 特許庁
The analysis section 52 determines the intensity component and phase component of second reflected light generated on the surface or in the interior of the observation object 9 on the basis of an interference light image obtained by setting an optical path length difference to be each target value successively by the phase shift method and photographing by the photographing section 51.例文帳に追加
解析部52は、位相シフト法により光路長差が各目標値に順次に設定されて撮像部51により撮像された干渉光像に基づいて、観察対象物9の表面または内部で生じた第2反射光の強度成分および位相成分を求める。 - 特許庁
A braking force control device for a vehicle that performs front and rear wheel distribution control of braking force by controlling individually braking pressures of left and right rear wheels such that, during braking, a wheel speed of a rear wheel takes on a value lying within a target control range that satisfies a predefined relationship with respect to a wheel speed of a front wheel.例文帳に追加
制動時に後輪の車輪速度が前輪の車輪速度に対し所定の関係を満たす目標制御範囲内の値になるよう左右後輪の制動圧を個別に制御することにより制動力の前後輪配分制御を行う車両用制動力制御装置。 - 特許庁
To provide a leader training supporting program, a leader training supporting method, and a leader training supporting apparatus for guiding, in the training of a project leader, so that the target skill value set by a trainee on skill items to be acquired in specialized skill and leader skill is adequate to the trainee.例文帳に追加
プロジェクトリーダの育成に関し、専門技術とリーダ技術の修得すべきスキル項目に対して修業者が設定した目標スキル値が適正であるようにガイダンスを行うリーダ育成支援プログラム、リーダ育成支援方法およびリーダ育成支援装置を提供することを目的とする。 - 特許庁
In this material testing machine 100, a changing speed of a stress or strain in a specimen is detected by a load cell 105 or an extensometer 106, and a pulse number P is determined based on a value of a deviation ΔV between a set target changing speed and a detected actual changing speed to control a rotating speed of a motor 1.例文帳に追加
材料試験機100は、供試体の応力または歪みの変化速度をロードセル105や伸び計106により検出し、設定された目標変化速度と検出した実変化速度との偏差ΔVの値によりパルス数Pを決定して、モータ1の回転速度を制御する。 - 特許庁
In the case that an outside air temperature T1 detected by an outside air temperature sensor 42 is below an outside air temperature judging value Thigh which judges an elevated temperature state of open air, a target refrigerant temperature Ttarget is established as a fiducial point Tint beforehand determined according to the cooling request of the fuel cell stack 1 under a photovoltaic action.例文帳に追加
外気温センサ42によって検出される外気温T1が、外気の高温状態を判定する外気温判定値Thigh以下の場合、目標冷媒温度Ttargetを、発電動作中の燃料電池スタック1の冷却要求に応じて予め決定されている基準値Tintに設定する。 - 特許庁
Thus, the recording paper P can be surely fed up to the carrier roller 20a, even when the slip quantity between the recording paper P and the paper feeding roller 7 is large, by continuing rotation of an LF motor 42, until the paper feeding roller 7 becomes a value or more of the target carrying quantity memory 302a.例文帳に追加
よって、給紙ローラ7が目標搬送量メモリ302aの値以上となるまで、LFモータ42の回転を継続することにより、記録用紙Pと給紙ローラ7との間のスリップ量が大きい場合でも、記録用紙Pを、搬送ローラ20aまで確実に給紙することができる。 - 特許庁
When the elapsed time reaches the target elapsed time value, the variation pattern determination means 115 finishes the reference of the special pattern selection table referred at present and sets the pattern selection table to be referred when determining the variation pattern this time or later, to another pattern selection table.例文帳に追加
変動パターン決定手段115は、経過時間が目標経過時間値に到達した場合に、今回以降で変動パターンを決定するときに参照すべきパターン選択テーブルを現在参照中の特殊パターン選択テーブルの参照を終了し他のパターン選択テーブルに設定する。 - 特許庁
If the terminal voltage VBAT reaches the charging target value of the battery cell 17, the counter circuit 13 measures an elapsed time afterward, and when elapsed time accords with the measured result, constant-current charge by a fixed current control circuit 9 to a switching circuit 11 is ended.例文帳に追加
端子電圧VBATが電池セル17の充電目標値に達すると、カウンタ回路13は以後の経過時間を計測して、経過時間が保持した計測結果に一致すると切替回路11に対し定電流制御回路9による定電流充電を終了させる。 - 特許庁
Then the target equivalent ratio KCMD is changed to a lean side predetermined value KOSO2L corresponding to the air-fuel ratio in a lean side of the theoretical air-fuel ratio, and dead time TNR from the time t1 of change to the time t2 when output SVO2 of the oxygen concentration sensor reaches first predetermined voltage SVO2W is measured.例文帳に追加
次に目標当量比KCMDを理論空燃比よりリーン側の空燃比に対応するリーン側所定値KOSO2Lに変更し、その時点t1から酸素濃度センサ出力SVO2が第1所定電圧SVO2Wに達する時刻t2までのむだ時間TNRを計測する。 - 特許庁
This inverse system sets a function sat(v) expressing the saturating characteristics in the pre-stage of a motor identification model G(s), and includes a linear or non-linear control controller for inputting a deviation e between the controlled variable y outputted from the motor identification model G(s) and the target value r when the signal v is inputted.例文帳に追加
逆システムでは、モータ同定モデルG(s)の前段に飽和特性を表す関数 sat(v)を置き、これに信号vを入力したときモータ同定モデルG(s)から出力される制御量yと目標値rとの偏差eを入力する線形又は非線形制御コントローラを含む。 - 特許庁
The image matching means 15, based on the detected value of the sensing means 12, determines epipolar constraint line in the image in the second point, contrasts the image part on the epipolar constraint line with a target part of the first point, and thus specifies the same part in each image.例文帳に追加
画像マッチング手段15は、センシング手段12の検出値に基づいて、前記第2地点での画像におけるエピポーラ拘束線を求め、当該エピポーラ拘束線上の画像部分と前記第1地点の対象部分とを対比することで、各画像内の同一部分を特定する。 - 特許庁
The fuel injection quantity is decided by adding the FF correction quantity DFF provided in correspondence with deviation from a theoretical air-fuel ratio of a target air-fuel ratio and the FB correction quantity DFB guard-treated in accordance with an output value of an air-fuel ratio sensor to the basic fuel injection quantity corresponding to the theoretical air-fuel ratio in this device.例文帳に追加
この装置では、理論空燃比に対応する基本燃料噴射量に、目標空燃比の理論空燃比からの偏移に応じて得られるFF補正量DFFと、空燃比センサの出力値に基づくガード処理されたFB補正量DFBとを加えて燃料噴射量が決定される。 - 特許庁
A head positioning control system has a correction system 20 which is added to a feedback control system for driving and controlling a plant 3 on the basis of a position error(e) from a target position (r) and calculates a correction value for compensating the position error(e) on the basis of the track-shaped distortion.例文帳に追加
ヘッド位置決め制御システムは、目標位置(r)との位置誤差(e)に基づいて、プラント3を駆動制御するフィードバック制御系に付加して、トラック形状歪に基づいて位置誤差(e)を補償するための補正値を算出する補正系20を有する構成である。 - 特許庁
An ECU 7 calculates the absolute velocity x' in the vertical direction of a vehicle body 1, calculates the relative velocity y' as the time differential of the displacement y of a damper, determines the target current value of the sky hook control based on the ratio x'/y', and controls the damping force to be conducted to a coil of each damper 20.例文帳に追加
ECU7は、車体1の上下方向の絶対速度x′を算出するとともに、ダンパの変位量y時間微分である相対速度y′を算出して、x′/y′にもとづいてスカイフック制御の目標電流値を決定し、各ダンパ20のコイルに通電する減衰力を制御する。 - 特許庁
When the count value is larger than the number of edges for deciding inversion, it is decided that the objective is inverted to a direction different from a target moving direction and a process for moving it to the correct moving direction is performed in a step S11.例文帳に追加
比較の結果、カウント値の方が、反転と判定するためのエッジ数以上であった場合、対物レンズは、目標としている移送方向とは異なる方向に反転されたと判定され、ステップS11において、正しい、移送方向に移送させる為の処理が実行される。 - 特許庁
A target value of a correction amount is calculated based on histogram information and face information of the input image, the correction is performed based on the amount of correction using the luminance low frequency component and the tone curve correction according to operation of the user, to obtain a desired correction result.例文帳に追加
入力画像の顔情報、ヒストグラム情報を元に補正量の目標値を算出し、ユーザの操作に応じて輝度低周波成分を用いた補正とトーンカーブ補正を合わせて目標の補正結果が得られるように、それぞれに補正量を分配して補正処理を行う。 - 特許庁
The heat generation amount parameters Q_θ1 and Q_θ2 at two target crank angles θ1 and θ2 during compression stroke are calculated on the basis of the corrected output value Pfix_θ, while abnormal output sensitivity of the cylinder internal pressure sensor 44 is detected on the basis of the gradient K of the heat generation amount parameter Q_θ.例文帳に追加
また、補正出力値Pfix_θに基いて、圧縮行程中の2つの判定対象クランク角θ1,θ2における発熱量パラメータQ_θ1,Q_θ2を算出し、発熱量パラメータQ_θの勾配Kに基いて、筒内圧センサ44の出力感度の異常を検出する。 - 特許庁
More specifically, the compressor (11) has a frequency controlled by correcting a target value of at least one of the following, a blow-out temperature, an intake pressure, and a discharge pressure of the compressor (11) according to the continuation time of the ON signal or the continuation time of an OFF state.例文帳に追加
具体的には、上記ON信号の継続時間またはOFF状態の継続時間に応じて、吹き出し温度、圧縮機(11)の吸入圧力及び吐出圧力のうち少なくとも一つの目標値を補正し、これにより、上記圧縮機(11)の周波数を制御する。 - 特許庁
The discrimination unit 5 is comprised of a plurality of weak discrimination units of which the group study is performed by boosting and an adder which performs majority with weight to output of the weak discrimination units, and each weak discrimination unit uses difference in luminance values of two pixels as feature quantity to output an estimation value for estimating whether or not the respective window images are the target objects.例文帳に追加
判別器5は、ブースティングにより集団学習された複数の弱判別器とこれらの出力を重み付き多数決する加算器とからなり、各弱判別器は、2つの画素の輝度値の差を特徴量とし対象物か否かを推定する推定値を出力する。 - 特許庁
When the slip control is in progress, if a value obtained by correcting, on the basis of a slip revolution speed, an actual transmission ratio being a ratio of an input revolution speed to an output revolution speed of this automatic transmission is out of a predetermined range of a target transmission ratio, abnormality is determined to occur in the automatic transmission.例文帳に追加
スリップ制御中は、自動変速機の出力回転数に対する入力回転数の比である実際の変速比をスリップ回転数に基づき補正した値が、目標変速比の所定範囲外であるときには、変速機内に異常が発生していると判定することとした。 - 特許庁
When the fixed position dog exists in front of the common reference dog (S34, YES), A=D is set as the initial value of the number of the dog being the target of the change of the dog number (S35), and D+Y is set as the new dog number of the dog designated by the variable A (S36).例文帳に追加
共通基準ドグの前方に定位置ドグが存在する場合には(S34,YES)、ドグ番号の変更の対象となるドグの番号の初期値としてA=Dを設定し(S35)、変数Aで指定されるドグの新たなドグ番号としてD+Yを設定する(S36)。 - 特許庁
To construct a control system which enables the acquisition of an optimum response by feeding back the estimated value of controlled variable for a control object, having a response target calculating means for calculating the controlled variable of the control object, and controlling to targeted response, and also, by controlling the control object output without overshooting.例文帳に追加
制御対象制御量の推定値をフィードバックし、制御対象制御量応答目標算出手段を持ち、目標とする応答に制御し、また、オーバーシュートすることなく制御対象出力を制御し、最適な応答が得られる制御系を構築する。 - 特許庁
Consequently, insufficient amount of suction air caused by adhesion of deposit on the intake system is suppressed, and deviation of an average air-fuel ratio of all the cylinders #1 to #4 to a rich side from a theoretical air-fuel ratio being a target value due to the insufficiency in combustion of homogeneous air-fuel mixture at the theoretical air-fuel ratio is suppressed.例文帳に追加
従って、吸気系へのデポジットの付着に伴う吸入空気量の不足が抑制され、その不足に伴い均質混合気の理論空燃比での燃焼時に全気筒#1〜#4の平均空燃比が目標値である理論空燃比からリッチ側にずれることは抑制される。 - 特許庁
The third correcting means 572 corrects/increases the upper limit value of the target rotational frequency of the fan 2 corrected by the first correcting means 55 after the determining means 56 determines that the increase of power supply to the fan 3 is possible until it is determined that the increase is impossible.例文帳に追加
第3補正手段572は判定手段56によりファン3への電力供給量が増大可能であると判定された後、増大不可能であると判定されるまで、第1補正手段55により補正されるファン2の目標回転数の上限値を増大補正する。 - 特許庁
In the steering control device for the vehicle for detecting a cruising lane and causing the vehicle to travel and follow the cruising lane, a target yaw rate γ* is set at a value of (4V/LS^2).ΔyS by using a forward watch point lateral deviation ΔyS, a vehicle speed V, and a forward watch point distance LS.例文帳に追加
走行車線を検出して当該走行車線に沿って車両を追従走行させる車両の操舵制御システムにおいて、目標ヨーレートγ^*を、前方注視点横変位△y_S、車速V、前方注視点距離L_Sを用い、(4V/L_S^2)・△y_Sの値となるように設定した。 - 特許庁
The electric power steering device is equipped with the main power supply B to supply the power to the motor, not illustrated, for assisting the steering motion and the auxiliary power supply EC for supporting the main power supply B according to necessity, and is to perform assisting the steering motions by feeding the decided target amperage to the motor on the basis of the value of steering torque.例文帳に追加
操舵補助用のモータ(図示せず)に電源を供給する主電源Bと、主電源Bを必要に応じて補助する補助電源ECとを備え、操舵トルク値に基づき、モータに流すべき目標電流値を定めて流すことにより操舵補助する電動パワーステアリング装置。 - 特許庁
To input a material in quantity in accordance with an output demanding value to be demanded by a fuel battery as much as possible while maintaining temperature of an evaporator at target control temperature by controlling material input quantity in consideration of a heat balance of an evaporator itself.例文帳に追加
蒸発器自体の熱量収支を考慮して原料投入量を制御することにより、蒸発器温度を目標管理温度に維持しながら、可能な限り燃料電池で要求する出力要求値に応じた量の原料を蒸発器に投入できるようにする。 - 特許庁
Then, the calculated rotational frequency compensating coefficient k is outputted to the fan drive control unit corresponding to the normal cooling fan and rotational frequency target value is varied by the rotational frequency compensating coefficient k by the fan drive control unit adjusted by the rotational frequency compensating coefficient k.例文帳に追加
そして、協調制御部58は、その算出した回転数補正係数kを正常な冷却ファンに対応するファン駆動制御部へ出力し、回転数補正係数kを受けたファン駆動制御部は、回転数補正係数kによって回転数目標値を変更する。 - 特許庁
To provide a duplex automatic switching control device for fluid distribution line capable of automatically switching a regulating valve while minimizing the fluctuation of a control target value, and reducing the cost while avoiding enlargement of its actuator part without extending the range of the regulating valve.例文帳に追加
制御対象値の変動を最小限に抑えつつ調節弁の切り換えを自動で行い得ると共に、調節弁のレンジを広げることなく、そのアクチュエータ部分の大型化を回避してコストダウンを図ることができる流体流通ラインの二重化自動切換制御装置を提供する。 - 特許庁
To provide an induction heating cooking device with enhanced convenience that can detect power consumption of each coil without adding a new circuit for power detection on coils side arranged in a concentric circular pattern and reduce uneven heating by means of performing feedback control on power of each coil to a target value.例文帳に追加
同心円状に配置した複数のコイル側に電力検知用の回路を新たに追加することなく、各コイルの消費電力を検知することができ、各コイルの電力を目標値にフィードバック制御することにより加熱ムラを低減し、利便性を向上させた誘導加熱調理器を得る。 - 特許庁
When the vibration frequency approximates the computed natural frequency, the elevator control device 13 controls a speed target value for the passenger car 3 to deviate from a range where the vibration frequency influences comfort, namely, a range of the natural frequency or its vicinity.例文帳に追加
エレベータ制御装置13は、この加振周波数が、演算済みの固有振動数に接近している場合には、加振周波数が乗り心地に影響する範囲、つまり固有振動数もしくはその前後の範囲から離れるように乗りかご3の速度目標値の制御を行なう。 - 特許庁
To provide a controller for an internal combustion engine capable of solving problems caused by combustion by improving convergency to a target value and improving responsiveness and stability of control in feedback control of fuel injection and ignition timing based upon combustion information.例文帳に追加
燃焼情報に基づく燃料噴射や点火時期のフィードバック制御において、目標値への収束性を向上して制御の応答性や安定性を向上させることで、燃焼に起因する問題を解消することのできる内燃機関の燃焼制御装置を提供すること。 - 特許庁
In the clutch changeover period, the control unit 300 changes the torque transfer path by raising the clutch torque capacity of the next gear side clutch to a target value out of the first clutch 74 and the second clutch 75, and then lowering the clutch torque capacity of the previous gear side clutch.例文帳に追加
この制御部300は、クラッチ掛け替え期間において、第1クラッチ74及び第2クラッチ75のうち、次段側のクラッチのクラッチトルク容量を目標値に上げた後に、前段側のクラッチのクラッチトルク容量を下げることによってトルクの伝達経路を変更する。 - 特許庁
As such, by switching a current value supplied to the target non-use linear solenoid valve by the linear solenoid mode switching means 506, a pressure-adjusted state is attained in which the flow-rate consumption of the linear solenoid valve is reduced to the minimum, and deterioration of control hydraulic pressure can be suppressed.例文帳に追加
このように、リニアソレノイドモード切替手段506が対象となる不使用のリニアソレノイドバルブに供給する電流値を持ち替えることにより、リニアソレノイドバルブでの消費流量をできるだけ少なくした調圧状態として制御油圧の低下を抑制することができる。 - 特許庁
To optimally control toner concentration of two-component developer so as to obtain a high-quality color image having constant image density by changing both a target value for the control of a toner concentration sensor and a feedback control parameter in accordance with pixel area, developer stirring time and environmental variation.例文帳に追加
画素面積や現像剤撹拌時間、環境変動に応じて、トナー濃度センサ制御の目標値とフィードバック制御パラメータの両方を変更することで、2成分現像剤のトナー濃度を最適に制御して、画像濃度が一定の高品位なカラー画像を得ること。 - 特許庁
Pump base torque Tr is calculated from the target revolution number by a pump base torque operation part 42 and third pump reference suction torque T3r is subtracted from the pump base torque Tr by a reduction part 44 to calculate a reference value Tf of the maximum suction torque usable in the first and second hydraulic pumps 2, 3.例文帳に追加
ポンプベーストルク演算部42で目標回転数からポンプベーストルクTrを算出し、減算部44でポンプベーストルクTrから第3ポンプ基準吸収トルクT3rを減算して第1及び第2油圧ポンプ2,3で使用可能な最大吸収トルクの基準値Tfを算出する。 - 特許庁
If a pressure Pa detected by the pressure sensor reaches a target decompression value Pr before the elapsed time reaches a prescribed abnormality threshold time Ts, normal decompression state is determined, and the pressure is reduced by the decompressing pump until a decompression step time Tv elapsed.例文帳に追加
そして、経過時間が所定の異常閾値時間Tsに到達する前に圧力センサの検出圧力Paが減圧目標値Prに至った場合には、正常な減圧状態であると判定して減圧ステップ時間Tvが経過するまで減圧ポンプにより減圧を行う。 - 特許庁
Reference time set for each of master substrate and target substrate by a setting means (circuit for latency timer time setting) provided inside the initiator substrate for setting the reference value of the inputted to a time measuring means (latency timer circuit) for each bus cycle.例文帳に追加
イニシエータ基板内に設けた時間の基準値を設定する設定手段(レイテンシータイマー時間設定用回路)により各マスター基板及びターゲット基板毎に設定された基準時間(レイテンシータイマー時間)を各バスサイクル毎に時間計測手段(レイテンシータイマー回路)に入力する。 - 特許庁
To provide a charging apparatus for charging a battery of a power tool, capable of changing a reference voltage for determining whether a charging voltage for charging the battery reaches a target charging voltage to an arbitrary value in an appropriate range.例文帳に追加
電動工具のバッテリを充電する充電装置であって、バッテリを充電するための電圧である充電電圧が目標充電電圧に到達しているか否かを判定するための基準電圧を適切な範囲で任意の値に変化させることが可能な充電装置を提供する。 - 特許庁
The normalization process is the process of pixel value gradation conversion that approximates the degree of variance of pixel values to a predetermined level in each local region of a discrimination target image, and the local region is a region sized to include only one eye of a face to be discriminated.例文帳に追加
正規化処理を、当該判別対象画像における各局所領域について画素値の分散の程度が所定レベルに近づくように画素値の階調変換を行う処理とし、その局所領域を、判別すべき顔の目が1つのみ含まれる大きさの領域とする。 - 特許庁
意味 | 例文 (999件) |
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|