意味 | 例文 (999件) |
detection-valueの部分一致の例文一覧と使い方
該当件数 : 7972件
When an overvoltage detection circuit 15 detects that an input voltage Vin becomes not smaller than a prescribed maximum value Vmax and an overvoltage is inputted into an input terminal ADPIN, a switch element M1 is turned off and brought into a blocked state, and an output node OUT is made to output a divided voltage Vd which is generated by resistors R1, R2 as a voltage Vout.例文帳に追加
入力電圧Vinが所定の最大値Vmax以上になって入力端子ADPINに過電圧が入力されたことを過電圧検出回路15で検出すると、スイッチ素子M1をオフさせて遮断状態にすると共に出力ノードOUTに抵抗R1及びR2で生成した分圧電圧Vdを電圧Voutとして出力するようにした。 - 特許庁
A topology detection unit 19 inside an AV controller 2 detects a topology of a surround system and records it in an audio/video correction value memory 18 as topology information and when the topology is changed, a video signal delay unit 13 and an audio processing unit 14 perform lip-sync correction and time alignment by adjusting delay amounts of video signals and audio signals in accordance with the topology information.例文帳に追加
AVコントローラ2内部にあるトポロジー検出部19は、サラウンドシステムのトポロジーを検出し、トポロジー情報として音声/映像補正値メモリ18に記録を行い、映像信号遅延部13及び音声処理部14は、トポロジーが変更された際には、そのトポロジー情報に応じて映像信号及び音声信号の遅延量を調整することでリップシンク補正及びタイムアライメントを行う。 - 特許庁
An air fuel ratio learning routine calculates deviation quantity of air fuel ratio between target air fuel ratio and air fuel ratio detected by an air fuel ratio sensor 6 by using fuel evaporation concentration C detected in a concentration detection routine (step S 309) if the engine is under purging (step S302), and calculates learning correction value flaf for correcting the calculated air fuel ratio deviation quantity (step S310).例文帳に追加
空燃比学習ルーチンは、パージ実施中である場合(ステップS302)、濃度検出ルーチンにおいて検出した燃料蒸発濃度Cを用いて空燃比センサ6による空燃比と目標空燃比との空燃比ずれ量を算出し(ステップS309)、この算出した空燃比ずれ量を修正するための学習補正値flafを算出する(ステップS310)。 - 特許庁
In LD activation mode control of the image forming device, before detection of laser beams by both first and second BD sensors, laser diodes are controlled so that a light emission amount of the laser diodes in an image forming region of the photoconductor drums is equal to or smaller than a predetermined value: when both the first and second BD sensors detect laser beams, lighting control of the laser diodes is shifted to printing mode control.例文帳に追加
LD起動モード制御時において、第1BDセンサ及び第2BDセンサが共にレーザ光を検出するまでは、感光ドラムの画像形成領域におけるレーザダイオードの発光量が所定以下となるようにレーザダイオードを制御し、第1BDセンサ及び第2BDセンサが共にレーザ光を検出したときに、レーザダイオードの点灯制御を印刷モード制御に移行させる。 - 特許庁
The image display device is equipped with: an APL detection section 6 for detecting an average luminance level that is the featured value of the input video signal; a control microcomputer 8 for dynamically and variably controlling the light emission luminance of the back light source 9 on the basis of the detected APL; and an OSD section 1 for superposing an on-screen display image signal for OSD display on the input video signal.例文帳に追加
画像表示装置は、入力映像信号の特徴量である平均輝度レベルを検出するAPL検出部6と、検出されたAPLに基づいてバックライト光源9の発光輝度を動的に可変制御する制御マイコン8と、OSD表示用のオンスクリーン表示画像信号を入力映像信号に重畳するOSD部1とを備えている。 - 特許庁
The vehicle operating system provided with a vehicle speed sensor 41, an operation lever 10, and an operation position sensor 26 detecting a position of the operation lever 10 is provided with an engine control device 44 driving the vehicle and a brake control device 45 according to detection value of the operation position sensor 26, and a longitudinal direction reaction force generating mechanism 20 applying reaction force to the operation lever 10.例文帳に追加
車速センサ41と、操作レバー10とその位置を検出する操作位置センサ26とを備えた車両操作装置に、操作位置センサ26の検出値に応じて、車両を走行させるエンジン制御装置44と車両を停止させるブレーキ制御装置45、および操作レバー10に反力を付与する前後方向反力発生機構20を設けた。 - 特許庁
An exhaust emission control device is provided with: the oxidation catalyst 12; a reducing agent supplying device 16 supplying a reducing agent into exhaust gas led to flow into the oxidation catalyst; a temperature sensor 44 detecting temperature of exhaust gas led to flow out from the oxidation catalyst; and a catalyst degradation diagnosis means 30 diagnosing degradation of the oxidation catalyst based on a value detected by an outflow exhaust gas temperature detection means.例文帳に追加
排気浄化装置は、酸化触媒12と、酸化触媒に流入する排気ガス中に還元剤を供給可能な還元剤供給装置16と、酸化触媒から流出する排気ガスの温度を検出する温度センサ44と、流出排気温度検出手段の検出値に基づいて酸化触媒の劣化を診断する触媒劣化診断手段30とを具備する。 - 特許庁
An injection molding machine is provided with a displacement detection sensor fitted with a fixed die plate or a movable die plate, a body to be detected by the sensor, and a controller for controlling the mold clamping force of a mold by a combined compression displacement value of the fixed mold and the movable mold detected by the sensor and the body to be detected.例文帳に追加
固定ダイプレート又は可動ダイプレートに取付けた変位量検出センサと、可動ダイプレート又は固定ダイプレートに取付けた変位量検出センサの被検知体と、前記変位量検出センサと前記被検知体とで検出した固定金型と可動金型の組合わせ圧縮変位値によって金型の型締力を制御する制御装置を備えた射出成形機。 - 特許庁
A sine wave output from the resolver is amplified and subjected to analog-digital conversion, and then a frequency component in a prescribed band wherein the frequency of an excitation signal is used as a center frequency is taken out through a band pass filter, and sampled synchronously with a reference signal based on the excitation signal, and a sine value of a detection angle signal is generated from the sampled signal.例文帳に追加
レゾルバからの正弦波出力を増幅してアナログ−デジタル変換したのち、帯域通過フィルタを通して励磁信号の周波数を中心周波数とする所定の帯域の周波数成分を取り出して、前記励磁信号に基づくリファレンス信号と同期させてサンプリングし、このサンプリングされた信号から検出角度信号の正弦値を作成する。 - 特許庁
To provide a robot device which selects either detection value of an angular velocity sensor or an acceleration sensor corresponding to the movement vector of an arm by using the angular velocity sensor and the acceleration sensor, converging the vibration generated when the movement of the arm is stopped by the generated control signal in a short time, and has the high operation speed and the high stop position of the arm, and its control method.例文帳に追加
角速度および加速度センサーを用いて、アームの移動ベクトルに対応して角速度もしくは加速度センサーのどちらかの検出値を選択し、生成された制御信号によりアームの移動停止時に発生する振動を短時間に収束させ、アームの速い作動速度と高い停止位置精度を有するロボット装置とその制御方法を提供する。 - 特許庁
A pyroelectric element layer including pyroelectric elements 10, 11, and 12, which include a pyroelectric body 2 where the value of spontaneous polarization varies with increase of temperature to create surface charge, an upper electrode 3 arranged on top surface of the pyroelectric body 2, and a lower electrode 4 arranged on bottom surface of the pyroelectric body 2 configures the infrared detection element 100 containing two or more-layered pyroelectric element layer arranged at upside and downside thereof.例文帳に追加
温度の上昇により自発分極の値が変化し、表面電荷を生じる焦電体2と、焦電体2の上面に配置された上部電極3と、焦電体2の下面に配置された下部電極4を有する焦電素子10,11,12から成る焦電素子層が上下に配置された、2層以上の焦電素子層を含む赤外線検出素子100を構成する。 - 特許庁
The first water supply apparatus BP1 and the second water supply apparatus BP2 have pumps respectively, and the second water supply apparatus BP2 issues an alarm indicating that the charged pressure of the pressure tank 30 is not in a normal range when the suction side pressure of the second water supply apparatus BP2 drops to a predetermined pressure drop detection value when starting the pump of the second water supply apparatus BP2.例文帳に追加
第1の給水装置BP1および第2の給水装置BP2はそれぞれポンプを有しており、第2の給水装置BP2は、該第2の給水装置BP2のポンプ始動時に第2の給水装置BP2の吸込側圧力が所定の圧力低下検出値にまで低下した場合は、圧力タンク30の封入圧力が正常範囲内にないことを示す警報を発する。 - 特許庁
In order to solve the problem, in this system, a control part 1 of a master device TR1 controls the period of synchronizing signals on the basis of a value of an actual frequency deviation of an oscillator used for the oscillating device 6, and thus, power consumption due to transmission of the synchronizing signals and detection of time deviation ΔT is suppressed while preventing synchronization loss of the synchronizing signals to prolong the service life of batteries.例文帳に追加
これに対して本実施形態では、発振器6に使用される発振子の実際の周波数偏差の値に基づいて、親器TR1の制御部1が同期信号の周期を調整しているので、同期信号に対する同期外れを防ぎつつ、同期信号の送信と時間ずれΔTの検出に伴う電力消費を抑えて電池寿命の延長を図ることができる。 - 特許庁
To precisely conduct an abnormality diagnosis of an AC generator when controlling power generation by arranging the AC generator which can freely change a power generation amount by using an ECM control signal of a control means, and by arranging a current detection means which can detect a load current value of an electric load, in a power generation control device of the AC generator.例文帳に追加
交流発電機の発電制御装置において、制御手段のECM制御信号によって発電量を自由に変更することができる交流発電機を設けるとともに電気負荷の負荷電流値を検出することができる電流検出手段を設けて発電制御をする場合に、交流発電機の異常診断を正確に実施することにある。 - 特許庁
Then, the ECU determines, based on a detection value of a forward radar sensor, etc., the presence of an intersecting vehicle at the temporarily stop intersection when the own vehicle goes through the stop intersection, the presence of a preceding vehicle at the temporarily stop intersection when the own vehicle goes through the stop intersection, and the preceding vehicle's stopping behavior at the temporarily stop intersection.例文帳に追加
続いて、ECUは、前方レーダセンサの検出値等に基づいて、自車両が一時停止交差点を通過するときに一時停止交差点に交差車両が存在しているかどうか、自車両が一時停止交差点を通過するときに一時停止交差点に先行車両が存在しているかどうか、一時停止交差点での先行車両の一時停止行動を判定する。 - 特許庁
The optical motion detection circuit includes a plurality of optical detectors 10, each of which has output, a memory including a reference frame with a digitized output value of an optical detector and a digitized sample frame of the optical detector obtained next to the reference frame and a comparison frame is further correlated to the sample frame to confirm motions of the directions of the first and the second axes.例文帳に追加
光学式動き検出動回路は、それぞれ出力を有する複数の光検出器10と、光検出器のディジタル化された出力値の基準フレームと、基準フレームの次に得られる光検出器のディジタル化されたサンプル・フレームとを含むメモリを含み、さらに、比較フレームがサンプル・フレームと相関付けられて、第1の軸と第2の軸の方向の動きを確認する。 - 特許庁
The optical fiber characteristic measuring device 1 includes the synchronous detector 21 for detecting synchronously a detection result of the photodetector 20 by using a synchronous signal having a prescribed frequency, and a frequency setting part 24a for changing the frequency of the synchronous signal when the modulation frequency in the light source 11 is an integer-fold value of the frequency of the synchronous signal.例文帳に追加
この光ファイバ特性測定装置1は、所定の周波数を有する同期信号を用いて光検出器20の検出結果を同期検波する同期検波器21と、光源11における変調周波数が上記の同期信号の周波数の整数倍である場合に、上記の同期信号の周波数を変更する周波数設定部24aとを備える。 - 特許庁
Then, the pointing device constituted like this is fixed to the inside of a keyboard input device and when an operator inclines the upper end of the cylinder 1 projecting into respective key tops, a distortion value is outputted from each detection sensor in accordance with its tilt angle and a control part controls the position of the cursor on the display in an optional direction based on these output signal.例文帳に追加
そして、このように構成されたポインティングデバイスをキーボード入力装置の内部に固定し、操作者が各キートップ間に突出する柱状体1の上端部を傾倒すると、その傾倒角に応じて各検知センサから歪値が出力され、制御部がこれら出力信号に基づいてディスプレイ上のカーソル位置を任意方向に制御するようにした。 - 特許庁
To provide a fiber drawing tension measuring method and a device and a tension control device capable of heightening control reliability of an automatic control operation and guaranteeing stable production of a highest- quality optical fiber, by enabling accurate detection of a natural frequency peak value and by enabling accurate drawing out by using a tension having a calculated optimum drawing condition different in each base material.例文帳に追加
固有振動数ピーク値を精度良く検出することを可能と成し、以て、各母材毎に異なる最適線引き条件を算出した張力を用いて正確に引出し得るようにすることにより、自動制御運転の制御信頼性を高めて最高品質の光ファィバの安定生産を保証させる線引き張力測定方法及び装置並びに張力制御装置の提供。 - 特許庁
In a device for detecting and correcting the color misregistration and density of each color toner image which may be generated in the image forming apparatus, light quantity set values in detecting color misregistration and in detecting density are individually determined in the light emitting and receiving sensor systems and a suitable light quantity value is set at each detection to perform highly accurate color misregistration correction and density correction.例文帳に追加
画像形成装置において発生する各色トナー像の色ずれ及び濃度を検出・補正する装置について、発光、受光センサの系において色ずれ検出時と濃度検出時の光量設定値を各々別々に決定し、それぞれの検出時に適切な光量値を設定することで、高精度な色ずれ補正及び濃度補正を行うことを可能にする構成。 - 特許庁
A digital circuit part 14 detects failure of a voltage detection part (including the AD front stage part 11, the AD converter 12, and a reference voltage generation part 15) while a voltage value of a digital voltage signal from the AD converter 12 is settled within the prescribed voltage range on the basis of the output of the AD converter 12 and the output of the voltage level determination part 13.例文帳に追加
デジタル回路部14は、AD変換器12の出力及び電圧レベル判定部13の出力に基づき、AD変換器12からのデジタル電圧信号の電圧値が前記所定電圧範囲内に収まっている状態における電圧検出部(AD前段部11、AD変換器12、基準電圧発生部15を含む)の故障を検出する。 - 特許庁
The system interconnection protective device comprises a voltage transformer 38 for detecting the AC voltage signal of an AC power system, a circuit 30 for operating the effective value of an AC voltage signal detected by the voltage transformer 38, and a frequency detection means 41 comprising a divider 31, a filter circuit 32, a comparator 35, a counter circuit 36, and a reciprocal operating unit 37.例文帳に追加
交流電力系統の交流電圧信号を検出する計器用変圧器38と、38によって検出された交流電圧信号を、実効値演算回路30、除算器31、フィルタ回路32、コンパレータ35、計数回路36、逆数演算器37からなる周波数検出手段41により、交流電力系統の交流電圧信号の周波数を検出する。 - 特許庁
To provide a method for automatically calibrating a detection level in a measuring part of a shutter testing machine, in which manual adjusting operation of an adjusted value VR is eliminated and an output level of a comparator to electric output (voltage) of reflected light is automatically set just by opening the shutter of a camera, whereby the shutter speed of the camera is easily, speedily and accurately detected.例文帳に追加
人手による調整値VRの調整操作を無くし、カメラのシャッタを開くだけで自動的に反射光の電気出力(電圧)に対するコンパレータの出力レベルを設定できるようにし、これによってカメラのシャッタスピード検出を簡便かつスピーディに精度よく行うことができるようにしたシャッタ試験機の測定部における検出レベルの自動校正方法を提供すること。 - 特許庁
This adaptive modulation system controlling method is to estimate a transmission line condition from the relation between an uncorrectable error occurrence condition due to error detection results and an error correction condition by the path metric value of Viterbi decoding, to select a modulation system in a transmitter and also to adjust a threshold at which a proper range to decide the error correction condition is specified.例文帳に追加
誤り検出結果による訂正できない誤りの発生状況と、ビタビ復号のパスメトリック値による誤りの訂正状況との関係から伝送路状況を推定し、送信装置における変調方式を選択すると共に、誤りの訂正状況を判断する為の適正範囲を特定しているしきい値を調整する適応変調方式制御方法である。 - 特許庁
The menu display device is provided with a display means for listing and displaying the plurality of items including the image quality adjustment and the setting values, an input means 5 for selecting the item in the list display and instructing the change of the setting value of the item, and an illuminance / chromaticity detection means 37 for detecting the illuminance and chromaticity of a device when the respective items are set to the present setting values.例文帳に追加
このメニュー表示装置は、画質調整を含む複数の項目とその設定値を一覧表示する表示手段と、一覧表示中の項目を選択して、その項目の設定値を変更指示する入力手段5と、各項目が現在の設定値に設定されたときの装置の照度、色度を検出する照度・色度検出手段37を備えている。 - 特許庁
An adding circuit 15 sets weighting for the control using the thermistor 10 and the control using the wavelength locker and continuously varies the weighting according to the difference between output power which is detected by a detection part 31 and varies with time and a target value to perform light emission control under the control using the thermistor 10 and the control using the wavelength locker in combination.例文帳に追加
サーミスタ10を用いた制御と波長ロッカを用いた制御に加算回路15で重み付けを設定し、かつ検出部31で検出されて経時的に変化する出力パワーと目標値の差分に応じて、加算回路15がこの重み付けを連続的に変化させて、サーミスタ10を用いた制御と波長ロッカを用いた制御を併用させて発光制御を行う。 - 特許庁
When the poisoning amount in the first region detected by the poisoning amount detection section 14 is a predetermined value or more, the gas sensor device 1 applies a second voltage higher than the first voltage to the contact combustion type gas sensor 21 so that a second region wider than the first region of the contact combustion type gas sensor 21 has a combustion temperature for combusting polar gas or higher.例文帳に追加
被毒量検出部14により検出された第1領域における被毒量が所定値以上となる場合、ガス検出装置1は、接触燃焼式ガスセンサ21の第1領域よりも広い第2領域が有極性ガスを燃焼させる燃焼温度以上となるように、接触燃焼式ガスセンサ21に第1電圧よりも高い第2電圧を印加する。 - 特許庁
In an insulation resistance meter 2, an application voltage of a predetermined value is injected from an AC voltage injector 15 through a resistance circuit 11 for detection to the object 9 to be measured, and information obtained from a current flowing to the object 9 to be measured is electrically processed through a band pass filter 12, thereby easily performing operation without requiring any mechanical operation mechanism.例文帳に追加
絶縁抵抗計2では、交流電圧注入器15から検出用抵抗回路11を通して被測定物9に向けて、所定の値の印加電圧を注入し、被測定物9に流れる電流から得られた情報を、バンドパスフィルタ12を通して電気的に処理可能とすることで、機械的な動作機構を必要とせず、操作を容易に行い得るようにする。 - 特許庁
The imaging apparatus also includes: a dynamic range expansion mode for obtaining a synthesized image of an expanded dynamic range by synthesizing the plurality of images captured under different exposure levels based on the position deviation amount detected by the deviation detection section 210; and an exposure condition fixed mode for performing photographing after determining an exposure condition while fixing at least one of shutter speed, stop value and ISO sensitivity.例文帳に追加
また、異なる露光により撮像した複数の画像を、ずれ検出部210により検出した位置ずれ量を元に画像合成することにより、拡大されたダイナミックレンジの合成画像を得るダイナミックレンジ拡大モードと、シャッタースピード、絞り値、もしくはISO感度の少なくとも一つを固定して露出条件を決定し、撮影する露出条件固定モードを有する。 - 特許庁
This rotation angle detector subtracts an angle detection range frequency from an absolute value of a detected abnormality difference between an angle detecting main means 3 and an angle detecting sub-means 5, and detects the abnormality in the detecting means for detecting an angle position and the abnormality in the amplifying circuit for amplifying a signal therein to determine immediately abnormality of a rotation angle.例文帳に追加
主角度検出手段3と副角度検出手段5の間の検出異常差の絶対値から角度検出範囲度数を減算し、角度位置を検出する検出手段の異常およびその信号を増幅する増幅回路部の異常を検出して、即時に回転角度の異常の判定を行うことを特徴とする回転角度検出装置である。 - 特許庁
The interlocking state of the steering operation interlocking means is relatively constituted to be released based on a tilt detection result more than a predetermined value of a tilting sensor for detecting the longitudinal tilt of the machine body.例文帳に追加
本発明は、ステアリングハンドルの旋回操作に連動して左右の走行車輪へのサイドクラッチ又はサイドブレ−キのうち旋回内側のものを作動させる操向操作連動手段を設け、機体の前後傾斜を検出する傾斜センサの所定以上の傾斜検出結果に基づき、前記操向操作連動手段の連動状態を解除すべく関連構成してあることを特徴とする。 - 特許庁
An amplifier which amplifies a signal to be amplified by a predetermined amplifying element and outputs the amplified signal has a variable means which changes the resistance value of an output resistance for specifying an amplification degree, a current detecting means which detects the output current which flows to the output resistance, and a control means for controlling the variable means based on the detection results of this current detecting means.例文帳に追加
被増幅信号を所定の増幅素子で増幅して増幅信号を出力する増幅器であって、増幅度を規定する出力抵抗の抵抗値を可変する可変手段と、出力抵抗に流れる出力電流を検出する電流検出手段と、該電流検出手段の検出結果に基づいて可変手段を制御する制御手段とを備える。 - 特許庁
IN the configuration for acquiring bit information by detecting a difference among a plurality of electronic watermarks, the dispersion of electronic watermark patterns is reduced by executing pre-embedding or corrected embedding of an electronic watermark having a strength for canceling a detection value acquired by electronic watermark detecting to an original image concerning a plurality of electronic watermark patterns to become a difference detecting object.例文帳に追加
複数の電子透かしの差分検出によりビット情報取得を行なう構成において、差分検出処理対象となる複数の電子透かしパターンについて、元画像に対する電子透かしパターン検出処理により取得される検出値を相殺する強度の電子透かしパターンの予備埋め込み、または修正埋め込みを実行して、電子透かしパターンの分散を低減する。 - 特許庁
The method for correcting smear of a CCD solid state imaging device comprises first step for lowering the level of a large smear signal extracted from a smear detection line by regulating the gain thereof, and second step for suppressing horizontal noise of the smear signal by detecting the intermediate value of noise sequentially from each specified region of the smear signal in the horizontal direction.例文帳に追加
本発明のCCD固体撮像装置のスミア補正方法は、スミア検出ラインから抽出したスミア信号にゲイン調整を行って大きなスミア信号のレベルを低減する第1ステップと、スミア信号の水平方向の各指定領域から順次ノイズの中間値を検出して、スミア信号の水平方向のノイズを抑制する第2ステップとを有することを特徴とする。 - 特許庁
A transmitter transmits a microwave with high reliability by providing a self-check function where a carrier level detection circuit 11 monitors a difference of carrier levels of a video signal 1 and an audio signal 2 and a control circuit 14 controls a level variable device 6a so that this level difference (LIF-Ls1) reaches a preset specified value Ld1 for the purpose of proper readjustment of the carrier level.例文帳に追加
送信装置のセルフチェック機能として、映像信号1と音声信号2との搬送波レベル差を、キャリアレベル検知回路11で監視し、このレベル差(LIF−Ls1)が予め設定された規定値Ld1になるように、制御回路14よりレベル可変器6aを制御して、適宜再調整する機能を設けることにより、信頼性の高いマイクロ波伝送を行う。 - 特許庁
The machine tool includes a current detecting means for detecting the value of a current output to a driving motor driving the positioning table, a signal processing means for filtering detection signals from the current detecting means, and an overload detecting means for calculating an increase in the load torque of the driving motor from the output of the signal processing means and for detecting that the positioning table has collided with an obstacle.例文帳に追加
位置決めテーブルを駆動する駆動モータへの出力電流値を検出する電流検出手段と、この電流検出手段からの検出信号を濾波する信号処理手段と、この信号処理手段の出力から上記駆動モータの負荷トルクの増大を算出し、上記位置決めテーブルが障害物と衝突したことを検出する過負荷検出手段とを備えた。 - 特許庁
In the tapping method for a melting furnace, the brightness of the melt drained from a tap hole 11 is detected by a radiation type thermometer to determine the transition of a molten metal M of the melt to the molten slag B from the change of the detection value obtained by the radiation type thermometer and the tap hole 11 of the molten metal M is closed, based on this determination.例文帳に追加
溶融炉に於ける溶融メタルの出湯方法に於いて、出湯口11から流出する溶融物の輝度を放射型温度計により検出し、前記溶融物の溶融メタルMから溶融スラグBへの切り変わりを放射型温度計の検出値の変化から判別すると共に、当該判別に基づいて溶融メタルMの出湯口11を閉鎖する。 - 特許庁
Operation devices 20, 25, 30, 35, 40 are provided with a determining means 55 for obtaining actual pressure ratio through the compressor from parameters measured using measuring means 25, 30 for diagnosis of compression, a comparison means 45 for comparing the actual measured pressure ratio with the previously given value, and an error detection means 50 for detecting error in accordance with the result of comparison.例文帳に追加
運転装置(20、25、30、35、40)は、圧縮の診断のために、測定手段(25、30)を用いて測定されたパラメータから、圧縮器を介して実際の圧力比を求める確定手段(55)と、測定された実際の圧力比を前もって与えられている値と比較する比較手段(45)と、前記比較の結果に応じて、エラーを検出するエラー検出手段(50)と、を備える。 - 特許庁
The Doppler image generation part has a phase detection part outputting a Doppler shift signal configured by extracting a component of a prescribed Doppler shift amount from the wave reception signal, a body motion elimination part correcting the Doppler shift signal by a predetermined body motion elimination value, and a gain adjustment part variably adjusting a gain of an output signal of the body motion elimination part according to set input.例文帳に追加
そして、ドプラ画像生成部は、受波信号から所定のドプラ偏移量の成分を抽出してなるドプラ偏移信号を出力する位相検波部と、ドプラ偏移信号を予め定めた体動除去値によって補正する体動除去部と、体動除去部の出力信号の利得を設定入力に応じて可変調整するゲイン調整部を有する構成とする。 - 特許庁
Further, the semiconductor laser device LD1 is driven before the exposure scanning of the next scanning line is commenced at the time of an image formation, the output of the semiconductor laser device LD1 is so adjusted that the values of detected signals from the detection sensors 31 and 32 become equal to the reference value of light quantity, and the exposure scanning of the next scanning line is performed with adjusted output.例文帳に追加
そして、画像形成時において、次の走査ラインの露光走査が開始される前に、半導体レーザLD1を駆動させ、そのときの検出センサ31、32からの検出信号の値が、上記光量基準値と同じ値になるように半導体レーザLD1の出力を調整し、調整された出力で当該次の走査ラインの露光走査を行う。 - 特許庁
An information processor includes a sensor electrode whose capacitance changes according to an operation to an operation surface, a detection unit for detecting a displacement of an operation point on the operation surface based on a change in the capacitance, and a determination unit for determining a pressing to the operation surface based on a displacement of the capacitance value of the sensor electrode and a displacement of the operation point.例文帳に追加
本技術に係る情報処理装置は、操作面への操作に応じて静電容量が変化するセンサ電極と、前記静電容量の変化をもとに、前記操作面の操作ポイントの変位を検出する検出部と、前記センサ電極の静電容量値の変位と、前記操作ポイントの変位とをもとに、前記操作面への押圧を判定する判定部とを具備する。 - 特許庁
The image forming apparatus has a detecting means of detecting the value of a current outputted from a voltage applying means and a control means of controlling the voltage applied from the voltage applying means to the transfer member according to the detection result, and varies and controls the output voltage during image formation in transfer material passage according to the output result of control performed before transfer operation in the image formation.例文帳に追加
画像形成装置は、電圧印加手段により出力される電流値を検知する検知手段と、検知結果から電圧印加手段から転写部材に印加する電圧を制御する制御手段を有し、画像形成時の転写動作以前に行う制御の出力結果から、転写材通過時の画像形成時における出力電圧を可変制御する。 - 特許庁
The traveling object detection device is provided with: infrared sensors 12a and 12b as pyroelectric infrared sensors having a plurality of pyroelectric elements Ra to Re and La to Le arranged like an array; and a traveling support ECU 11 for determining presence of a traveling object around a vehicle 2 by comparing a moving average value based on either the difference or ratio of the outputs of adjacent pyroelectric elements with a threshold for moving average.例文帳に追加
アレイ状に複数配列された焦電素子Ra〜Re・La〜Leを有する焦電型赤外線センサである赤外線センサ12a・12bと、隣接する焦電素子間の出力の差および比のうちのいずれかに基づく移動平均値を移動平均用閾値と比較することによって車両2の周辺の移動体の有無を判定する走行支援ECU11と、を備える。 - 特許庁
The printer 100 includes: an edge detection unit 112, a screen processing unit 113, a pulse width conversion unit 114 for converting each pixel included in image data to C-bit (C≤A) pulse width data according to an input gradation value, and an output unit 115 for outputting pulse width data output from either of the screen processing unit 113 and the pulse width conversion unit 114.例文帳に追加
本発明の印刷装置100は、エッジ検出部112と、スクリーン処理部113と、画像データに含まれる各画素を入力階調値に応じたC(ただしC≦A)ビットのパルス幅データに変換するパルス幅変換部114と、スクリーン処理部113及びパルス幅変換部114のいずれかから出力されたパルス幅データを出力する出力部115と、を備える。 - 特許庁
A slide door device comprises the slide door 10 which is slidably arranged in a vehicle body 1, a door detecting means 70 for detecting the speed of the slide door 10 at least when the slide door 10 slides in a door opening direction, and a braking means 90 for applying braking to the slide door 10 when the result of detection by the means 70 exceeds a preset threshold value.例文帳に追加
車両本体1に対してスライド可能に配設したスライドドア10と、少なくともスライドドア10が開扉方向へスライドした場合にスライドドア10の速度を検出するドア検出手段70と、ドア検出手段70の検出結果が予め設定した閾値を超えた場合にスライドドア10に制動を加える制動手段90とを備えてスライドドア装置を構成している。 - 特許庁
Then the base station with RSSI detection value equal to or higher than a second threshold is selected, based on the retrieval information of each surrounding base station stored in the internal memory in the case of call origination or handover, the base station is immediately determined as connecting destination or handover destination and establishment control of a radio link channel is executed between a mobile communication terminal and the base station.例文帳に追加
そして、発呼時或いはハンドオーバ時において、上記内部メモリに記憶されている各周辺基地局の検索情報をもとにRSSI検出値が第2のしきい値以上の基地局を選択し、この基地局を接続先或いはハンドオーバ先として直ちに決定して、この基地局との間で無線リンクチャネルの確立制御を実行するようにしたものである。 - 特許庁
An electronic control unit 80 carrying out overall control of an operating state of the engine 1 calculates and stores (learns) a numeric value corresponding to each operating condition and capable of providing an optimum temperature rising effect in regard to each of a post injection quantity and an additional fuel quantity by feeding back a detection signal of a first exhaust temperature sensor 74a or a second exhaust temperature sensor 74b.例文帳に追加
エンジン1の運転状態を統括制御する電子制御装置80は、ポスト噴射量及び添加燃料量の各々について、各運転条件に対応して最適な昇温効果を得ることのできる数値(学習値)を第1排気温度センサ74a若しくは第2排気温度センサ74bの検出信号をフィードバックすることにより算出し、記憶(学習)する。 - 特許庁
In an information communication medium including a card body with a module embedded therein, the module includes a receiving means for receiving a power wave by communication with external equipment; a conversion means for converting the power wave received by the receiving means to DC voltage; and a voltage detection means for detecting an output voltage value of the DC voltage converted by the conversion means.例文帳に追加
モジュールが埋め込まれたカード本体により構成される情報通信媒体であって、前記モジュールは、外部機器と通信して電力波を受信する受信手段と、前記受信手段で受信した電力波を直流電圧に変換する変換手段と、前記変換手段で変換された直流電圧の出力電圧値を検知する電圧検知手段とを有する。 - 特許庁
When power is supplied to the main control board provided in the game machine which performs the big winning game when a random number for the big winning determination acquired for each entry to a start port and a predetermined big winning value match, an operation signal indicating that a prescribed operation is performed after the power supply is detected by a detection part 302.例文帳に追加
始動口の入賞ごとに取得される大当たり判定用乱数と、あらかじめ定められた大当たり値とが一致する場合に大当たり遊技をおこなう遊技機が備える主制御基板に対する電源の供給があった場合は、当該電源供給後に所定の操作がおこなわれたことを示す操作信号を検出部302によって検出する。 - 特許庁
Either of at least a metering pump 7 that quantitatively supplies the liquefied gas of carbon dioxide that becomes the liquefied gas of the carbon oxide to a heat exchanger 9 corresponding to the detection value of the near infrared spectroscopy sensor 10, and a metering pump 8 that quantitatively supplies the solvent components to the heat exchanger 9 is driven by the control of a moving phase controlling device.例文帳に追加
近赤外分光センサ10の検出値に応じて、二酸化炭素の超臨界流体となる二酸化炭素の液化ガスを熱交換器9に定量的に供給する定量ポンプ7、及び溶剤成分を熱交換器9に定量的に供給する定量ポンプ8の少なくともいずれかの運転を移動相組成制御装置によって制御する。 - 特許庁
意味 | 例文 (999件) |
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|