ON- OFFの部分一致の例文一覧と使い方
該当件数 : 27736件
This getting-on/off assisting device and a platform door device are integrated together, a control amplifier for driving the step is stored in a shutter case for the platform door so that the thickness of a part for storing the step is drastically thinned, thereby allowing shallow excavation depth for the platform, and large reduction of the installation construction cost.例文帳に追加
乗降補助装置とホームドア装置を一体化し、ステップ駆動用の制御増幅器をホームドア用戸袋の中に収納することによりをステップが収納される部分の厚さが大幅に薄くできるようになり、プラットホーム掘り下げる深さを浅くでき、設置工事費を大幅に減らすことが出来た。 - 特許庁
After the power supply is shut off to the attachment/detachment unit U, when the power supply is restarted, whether or not the electrical part P is electrically connected to a power source DC 13 is determined and when the electrical part P is not electrically connected, a guidance for work items for corresponding work is displayed on the LCD 122.例文帳に追加
着脱ユニットUへの電源供給の遮断後、電源供給が再開されると、電気部品Pが電源DC13と電気的に接続されたか否かが判断され、電気部品Pが電気的に接続されていない場合、LCD122に対応作業の作業項目がガイダンス表示される。 - 特許庁
In the substrate treatment system where a reaction chamber (1) is concatenated with a wafer carrying chamber (3) through a partition (2c), the partition (2c) is provided with a pipe (11) for interconnecting the reaction chamber (1) and the wafer carrying chamber (3) and the interconnecting pipe (11) is provided with an on/off valve (10).例文帳に追加
反応室(1)が、仕切部材(2c)を介してウエハ搬送室(3)に連接された基板処理装置であって、上記仕切部材(2c)に、上記反応室(1)とウエハ搬送室(3)とを連通する連通管(11)を設け、連通管(11)に連通管開閉バルブ(10)を設けた基板処理装置とする。 - 特許庁
Projective resin pots 4A are provided on the upside near gates of a lead frame 3 of a semiconductor device 1, remaining resin portions 4 outside the lead frame 3 are fixed, and the resin sealed semiconductor device 2 is turned together with the lead frame 3 to peel off the remaining resin portions 4 together with the projective resin pots 4A from the lead frame 3.例文帳に追加
半導体装置1のリードフレーム3のゲート部近傍の上部に凸状樹脂溜まり4Aを設け、前記リードフレーム3の外方の余剰樹脂部分4を固定し、前記リードフレーム3ごと樹脂封止半導体装置2を回転させて、前記凸状樹脂溜まり4Aごと余剰樹脂部分4をリードフレーム3から剥がす。 - 特許庁
Article 81 No aircraft shall be flown, except during taking off or landing, at an altitude lower than that specified by Ordinances of the Ministry of Land, Infrastructure, Transport and Tourism, taking into consideration the safety of persons or objects on land or water as well as the safety of aircraft; provided, however, that the same shall not apply when permitted by the Minister of Land, Infrastructure, Transport and Tourism. 例文帳に追加
第八十一条 航空機は、離陸又は着陸を行う場合を除いて、地上又は水上の人又は物件の安全及び航空機の安全を考慮して国土交通省令で定める高度以下の高度で飛行してはならない。但し、国土交通大臣の許可を受けた場合は、この限りでない。 - 日本法令外国語訳データベースシステム
(i) Building structures, plants and other objects present in the vicinity of an aerodrome, which are deemed by the Minister of Land, Infrastructure, Transport and Tourism that they have no adverse influence on the take-off or landing of aircraft. However, this shall not apply when said object are deemed securely removable by the scheduled completion date of the works of said an aerodrome. 例文帳に追加
一 空港等の周辺にある建造物、植物その他の物件であつて、国土交通大臣が航空機の離陸又は着陸に支障があると認めるものがないこと。ただし、当該空港等の工事完成の予定期日までに、当該物件を確実に除去できると認められる場合は、この限りでない。 - 日本法令外国語訳データベースシステム
To provide a curtain opening/closing device capable of easily opening/closing a curtain by hand without allowing its take-up or let-out string to run off the curtain rail and being made by modifying a conventional curtain very little and not on a large scale.例文帳に追加
巻き取り又は繰り出し用の紐体がカーテンレールから外れたりすることなく、手動で容易に、開閉することのできるカーテン開閉装置を提供する、並びに、通常のカーテンに極めて簡単な改造を施すだけでよく、大掛かりな改造工事を必要とすることのない、カーテン開閉装置を提供することを目的とする。 - 特許庁
At the abutting position of batteries 5a, 5b which are housed in series and are easy to come off due to vibration in a battery housing section 4, a hard wall 6 is arranged on one side and a flexible battery press member 7 is arranged at the opposite position thereto, thus holding both batteries 5a, 5b simultaneously.例文帳に追加
電池収納部4において、直列に収納された電池5a,5bが振動によって外れやすい電池5a,5bの当接位置にて、一方の側部に硬い壁部6を配置し、これに対向する位置に可撓性を有する電池押圧部材7を配置して両方の電池5a,5bを同時に保持するようにしている。 - 特許庁
When a positive or negative high voltage is applied to an input terminal 13, diodes 24, 25 clamp the received voltage to 6 V/-1 V, an intermediate voltage 3 V is applied to gates of FETs 17, 18, 21 and 22 to turn on/off the FETs 17-22 by a voltage between a gate potential and a source potential.例文帳に追加
入力端子13に、正極性、または負極性の高電圧が印加された場合はダイオード24,25によってその電圧を6V,−1Vにクランプし、FET17,18,21及び22のゲートには中間電位3Vを印加しておき、これらのFET17〜22をそのゲート電位とソース電位との電位差によってオンオフさせる。 - 特許庁
The logical integrated circuit 2 is provided with a selection terminal and a switch element 6 interposed between the output terminal 118 of the bus holding circuit 102 and the data input terminal 116 and the switch element 6 is turned ON when the logical level of the signals inputted to the selection terminal 4 is the logic '1' and is turned OFF when it is the logic '0'.例文帳に追加
論理集積回路2は、選択端子4と、バスホールド回路102の出力端子118とデータ入力端子116との間に介在するスイッチ素子6とを備え、スイッチ素子6は選択端子4に入力される信号の論理レベルが論理”1”のときオン、論理”0”のオフとなる。 - 特許庁
For instance, when the number of illuminants 5 to display (lighting ON, lighting OFF, flashing, etc.), at every prescribed amount (for instance 1000) in an illuminant group equipped with a prescribed number of elements (for instance 10) is changed, one recognized the information can almost instantly recognize a rough number 2 of game media.例文帳に追加
例えば所定の要素数(例えば10個)からなる発光体5を備えた発光体群4について、所定数量(例えば1000個)ごとに表示(点灯,消灯,点滅等)する発光体5の個数を変化させると、当該報知を認識した者は大体の遊技媒体数2をほぼ一瞬で認識できる。 - 特許庁
When the inner frame 12 or the front surface frame 14 is not opened (is closed) while the power of the Pachinko game machine 10 is turned off and the capacitor CD1 is kept in the charging state, the frame opening detection circuit 260 does not output the output signals SG4 when the power of the Pachinko game machine 10 is turned on.例文帳に追加
一方、枠開放検出回路260は、パチンコ機10の電源がオフされている間に内枠12または前面枠14が開放されず(閉鎖されており)、コンデンサCD1が充電状態のままであれば、パチンコ機10の電源がオンされたときに、出力信号SG4を出力しない。 - 特許庁
In addition, the output terminal 105M alternately outputs voltage (drive voltage VCOMH) according to charges stored in smoothing capacity C104-3 and voltage (drive voltage VCOML) according to charges stored in smoothing capacity C104-4 by alternative turning on/off of the switches SW5, SW6.例文帳に追加
また、スイッチSW5,SW6が交互にオン/オフになることによって、出力端子105Mは、平滑容量C104−3に蓄積された電荷に応じた電圧(駆動電圧VCOMH)および平滑容量C104−4に蓄積された電荷に応じた電圧(駆動電圧VCOML)を交互に出力する。 - 特許庁
An LD 11 of anode-common type or cathode-common type, a semiconductor switch, and a resistor are connected in series to form an LD current path, an automatic current control circuit 12 sets an LD current at a prescribed value turning the semiconductor switch ON or OFF so as to set the terminal voltage of the resistor at a prescribed value.例文帳に追加
アノードコモンタイプあるいはカソードコモンタイプのLD11と半導体スイッチと抵抗とを直列に接続してLD電流の通路を形成し、自動電流制御回路12は該抵抗の端子電圧が設定電圧になるように半導体スイッチをオン/オフ制御してLD電流を設定電流値にする。 - 特許庁
To provide a table top chain capable of providing a flat surface without pin holes and heads of connected pins protruding on the top surface of a top plate, and capable of horizontal circulation without coming off from an upper link plate even when load and impulsive force are applied, regardless of direction, to the top plate from the link plate.例文帳に追加
トッププレートの上面にピン孔、連結ピンの頭部等が露出しない平坦面のものとすることができ、上側リンクプレートに取り付けられたトッププレートが如何なる方向から荷重、衝撃力等の力を受けても、上側リンクプレートから外れない水平循環可能なテーブルトップチェーンを提供すること。 - 特許庁
Thereafter, turning on or off the discharge lamp is controlled so that the difference between the potential of the surface of the photoreceptor entering the nip between the charging roll and the photoreceptor and the potential of the charging roll is decreased and also the direction of an electric field between the charging roll and the photoreceptor entering the nip between the charging roll and the photoreceptor is changed.例文帳に追加
そしてその後、帯電ロールとのニップ部に突入する時点での感光体の表面電位と帯電ロールの電位との差が減少し、また、帯電ロールとのニップ部に突入する時点での感光体と帯電ロールとの間の電界の向きが変わるように、除電ランプのオン、オフを制御する。 - 特許庁
A hopper has a rotary disk operated by a motor, a count sensor arranged at a disk path from the rotary disk to the insertion slot, a shutter device selectively movable between the closing position and the opening position of the insertion slot and a controller for selectively moving the shutter device to the positions in connection with the on/off of the motor.例文帳に追加
モータにより作動される回転ディスクと、回転ディスクから投出口へのディスク通路に配置したカウントセンサと、前記投出口の閉鎖位置と開放位置に選択的に移動可能なシャッタ装置と、前記シャッタ装置を前記モータのオンオフに連動して前記位置に選択移動する制御装置とを有する。 - 特許庁
When the device is stopped for a given time, the ultraviolet irradiation means 42 is turned off and a container 46 on the rotating table 3 is disposed below the quartz pipe 44, and the substituting function for substituting the interior of an end section by jetting the given amount of the cationic ultraviolet curing composition 45 out of the dispenser 41 is added.例文帳に追加
装置が所定時間停止した際に、紫外線照射手段42を切り、回転テーブル3上の容器46を石英管44の下方に配置させ、ディスペンサ41からカチオン型紫外線硬化性組成物45を所定量吐出させて先端部内を置換させる置換機能を付加させる。 - 特許庁
This illumination control signal 105 is outputted even to a data signal converting means 104, which converts a data signal 102 into a data signal 103 so as not to cause positive/negative inversion of display of a liquid crystal panel 114 in synchronism with turn-on and turn-off of a light source 115.例文帳に追加
この点灯制御信号105は、データ信号変換手段104にも出力され、データ信号変換手段104では、光源115の点灯及び消灯の切換えに同期して、液晶パネル114における表示がポジネガ反転しないように、データ信号102をデータ信号103に変換する。 - 特許庁
The underwear makes it possible for a wearer to easily put on and off without up-and-down movement of the arms while the sleeve width of the underwear is the same or narrower as or than that of the conventional underwear.例文帳に追加
下着の袖の幅が従来のものと同じかそれ以下であっても、腕の上げ下げを必要とせず着脱が自在な下着において、袖8を構成する生地を伸縮自在なニット生地にて構成すると共に、袖8と見頃3の境界部分が,伸縮自在で析曲した人の腕が縦方向に挿通するまで伸張する。 - 特許庁
Further, a contact thermistor 62 is arranged in contact with an end of the elastic layer 53 of the heat roller 3a off the entire fixation area L, so even if the end of the elastic layer 53 flaws as the contact type thermistor comes into contact with the end, the flaw of the end never causes fixation unevenness on a recording form.例文帳に追加
また、全定着領域Lから外れる加熱ローラ3aの弾性層53の端部に、接触型サーミスタ62を接触させて配置しているので、接触型サーミスタ62の接触により弾性層53の該端部に傷が付いたとしても、この端部の傷が記録用紙の定着ムラの原因になることはない。 - 特許庁
The apparatus is characterized in that a plurality of exposure heads 10 each comprising optical members 16, 20 for exposure having a means 14 to selectively turn on/off a plurality of pixels and attached to an exposure head base 12, are arranged in a staggered state with the optical members 16, 20 for exposure adjacent to each other.例文帳に追加
複数の画素を選択的にon/offする手段14を有する露光用の光学部材16、20を露光ヘッドベース12に取り付けて構成されている複数の露光ヘッド10を、露光用の光学部材16、20同士が隣接する状態で千鳥配列して一体に構成したことを特徴とする。 - 特許庁
To provide a sensor remarkably miniaturizable, and having high performance or operation sensitivity, and having durability and high reliability, in a tilt detection sensor of a type having a plurality of electrodes and a conductive spherical body incorporated and structured so as to carry out on/off operation by rolling of the spherical body.例文帳に追加
複数の電極と導電性球体を内蔵し、該球体の転動によりオン・オフ動作を行わせるようにしたタイプの傾斜検知センサにおいて、大幅に小型化することができるとともに、性能ないし動作感度が高く、しかも耐久性及び高い信頼性のあるセンサを提供すること。 - 特許庁
In dissolving the scale formed on the cathode during the operation of the apparatus by an acidic electrolyte and stopping the apparatus for forming the electrolytic water, the gaseous chlorine accumulated in the forming apparatus is expelled by shutting off an electrolysis power source first, then feeding the acid electrolyte for a while and thereafter the apparatus is fully stopped.例文帳に追加
装置の運転中に陰極に生成するスケールを酸性電解液で溶かし、電解水生成装置を停止するにあたり、電解電源の遮断を先にして酸性の電解液を暫く送液することによって、生成装置の内部に溜まっている塩素ガスを追い出した後に装置を全停止する。 - 特許庁
To provide a horizontal-striped solid oxide type fuel cell bundle capable of improving power generation efficiency by reducing the temperature gradient in the bundle by setting off-gas combustion areas on both end faces in the horizontal-striped solid oxide type fuel cell bundle and capable of preventing damage of components of cells, a cell stack and the bundle.例文帳に追加
横縞方式の固体酸化物形燃料電池バンドルにおいて、オフガス燃焼域が両端面になるようにすることにより、バンドルにおける温度勾配を低減して、発電効率を改善し、セルやセルスタックやバンドルの構成部材の破損を防止することができる横縞方式の固体酸化物形燃料電池バンドルを得る。 - 特許庁
To provide a production system of a semiconductor device using a laser crystallization method which can prevent a grain boundary from being formed in a channel formation area of a TFT, and can prevent a conspicuous reduction in mobility of the TFT, a reduction in an on-current, or an increase in an off-current.例文帳に追加
TFTのチャネル形成領域に粒界が形成されるのを防ぎ、粒界によってTFTの移動度が著しく低下したり、オン電流が低減したり、オフ電流が増加したりするのを防ぐことができるレーザー結晶化法を用いた、半導体装置の生産システムの提供を課題とする。 - 特許庁
When a cycle timer 8 generates a timer output, detected temperature is compared with target temperature to perform write access which turns on a port P2 to an output port when the detected temperature is higher than the target temperature and turns off the port P2 to the output port 10 when lower.例文帳に追加
周期タイマ8からタイマ出力があると、検出温度と目標温度を比較し、検出温度が目標温度より高い場合は、出力ポート10にポートP2をオフするライトアクセスを行い、他方、検出温度が目標温度より低い場合は、出力ポート10にポートP2をオンするライトアクセスを行う。 - 特許庁
By connecting a gas introduction parts 4 and a gas diffusion parts 6 to the reinforcement rib 3 prepared for breakage prevention of the dielectric top board 2, a structure is constituted that gas is made to distribute uniformly on a substrate 9 in a vacuum processing room 8 from a gas blow-off hole 7 arranged in the gas diffusion parts 6.例文帳に追加
誘電体天板2の破損防止のために設けた補強リブ3にガス導入部品4およびガス拡散のための部品6を接続することで、ガス拡散のための部品6に設けたガス吹き出し穴7から真空処理室8内の基板9上にガスを均一に分布できる構造とした。 - 特許庁
To provide a control unit of a reformer for a fuel cell to keep a stable burning condition of a combustion burner during the on-off of a water supply route which supplies the water removed from anode gas etc. to a water storage tank, in a reformer for a fuel cell equipped with a combustion burner to heat the reforming catalyst.例文帳に追加
改質触媒を加熱する燃焼バーナを備えた燃料電池用改質器において、アノードガスなどから除去された水分を貯水タンクに供給する水分供給路を開閉させる際、燃焼バーナでの安定した燃焼状態を保持するようにした燃料電池用改質器の制御装置を提供する。 - 特許庁
By controlling operation of the electromagnetic on-off valve 24 with a controller 36 with a built-in computer, air in the air tank 18 is supplied while pressure is reduced to a predetermined pressure by the pressure reducing valve 20 from transmission start to synchronization completion and air in the air tank 18 is directly supplied from synchronization completion to transmission completion.例文帳に追加
そして、コンピュータを内蔵した制御装置36により電磁開閉弁24の作動を制御することで、変速開始から同期完了までは、エアタンク18のエアを減圧弁20により所定圧力に減圧しつつ供給する一方、同期完了から変速完了までは、エアタンク18のエアを直接供給する。 - 特許庁
To provide a magnetizer that does not cut off the magnetize current at peak and uses the first half wave of the resonance current to regenerate the residual energy in L1 and C1 when the magnetize current is supplied to the magnetizer coil L1 though ON control over the magnetizer switching element by means of the charging voltage of the charging capacitor C1.例文帳に追加
充電コンデンサC1の充電電圧により、着磁用スイッチング素子のオン制御で着磁コイルL1に着磁電流を供給する着磁器において、着磁電流をそのピーク値で遮断することなく、L1及びC1に共振電流の最初の半波を着磁電流とし、残留エネルギを回生する。 - 特許庁
To provide a golf club head that can maintain the strength of a face part and can suppress the repulsion of the face center within a rule conforming area while maintaining the face part lightweight and that can exhibit equal repulsion performance on the toe side and the heel side even if a ball is hit off the face center.例文帳に追加
フェース部の軽量化を維持しながら、フェース部の強度も維持するとともに、フェースセンターの反発性をルール適合範囲内に抑えることができるとともに、フェースセンターから外れてボールを打った場合でも、トウ側でもヒール側でも均等な反発性能を発揮することができるゴルフクラブヘッドを提供する。 - 特許庁
In the transparent pressure-sensitive adhesive film which produces no paste residue on an adherend when peeled off, a transparent plastic base layer, a transparent porous layer formed by a sol-gel process and containing fine particles consisting mainly of silica and/or titania, and a transparent pressure-sensitive adhesive layer are stacked in this order.例文帳に追加
剥離した際に被着体に糊残りを生じない透明粘着フィルムであって、透明プラスチック基材層、シリカ及び/又はチタニアを主成分とする微粒子を含有するゾル・ゲル法によって得られる透明多孔質層、並びに、透明粘着剤層がこの順に積層されている透明粘着フィルム。 - 特許庁
An input panel 181 connected to the input detection part 180 is provided with: an intention transmission switch 152 turned on/off to input switch information so as to intentionally input intention of the user by the user oneself; and an inference mode selection switch 153 selecting an arbitrary inference mode from a plurality of inference modes.例文帳に追加
また、入力検知部180に接続された入力パネル181には、利用者自身がみずからの意思を意図的に入力するために、オン・オフしてスイッチ情報を入力する意思伝達スイッチ152と、複数の推論モードから任意のものを選択する推論モード選択スイッチ153が設けられている。 - 特許庁
To make a telephone call by selecting the ON/OFF setting of the echo cancelar for each telephone call, the best setting of the echo cancelar can be inserted when an opposite party who has the telephone call by termination or origination has the same telephone number once the settings of the telephone number of the opposite party and the echo cancelar are stored in a memory part 11b.例文帳に追加
一通話毎にエコーキャンセラのON/OFF設定を選択して通話したい場合、一度、相手先の電話番号とエコーキャンセラの設定がメモリ部11bに記憶されると、着信あるいは発信して通話する相手先が同一の電話番号であるときに、最適のエコーキャンセラの設定を挿入することが可能になる。 - 特許庁
To provide a gutter hanger which is installed simply on a folded plate roof and does not cororate together with a nut and in which a fixing member functions as a stopper, the gutter hanger can be fixed onto a hanging bolt by the fixing member and the nut and clamping is not loosened by external force such as wind and snow and vibrations after the execution of works and the nut does not slip off.例文帳に追加
折板屋根に取付が簡単で、ナットとも回転させることなく、係止部材がストッパーになり、係止部材とナットとで樋支持具を吊りボルトに固定させることができ、施工後、風雪等の外力や振動によって、締付が緩んで、ナットが外れることがない樋吊り具を提供するものである。 - 特許庁
According to the method for manufacturing a needle-shaped body, since a transfer plate where a fine recessed part is formed at a pedestal part having a slope on a side wall is used, stress as the needle-shaped material contracts operates so as to peel the transfer plate and the filled needle-shaped material off each other when the needle-shaped material hardens and contracts.例文帳に追加
本発明の針状体製造方法は、側壁に傾斜を有する台座部に微細凹部が形成された転写版を用いることから、針状体材料の硬化収縮にあたり、針状体材料の収縮に伴う応力が、転写版と充填された針状体材料とを剥離する方向に働く。 - 特許庁
When the auxiliary port 41 is disconnected from the input port 14, the detection pressure changeover valve 43 is switched to the fail-safe determination side, and the oil pressure switch SW is supplied with the same driving oil pressure as the frictional engaging device CL, and "the fail-safe determination" can be carried out from an ON-OFF state of the oil pressure switch SW.例文帳に追加
また、補助ポート41が入力ポート14と遮断されると検出圧切替弁43がフェールセーフ判定側へ切り替わり、油圧スイッチSWに摩擦係合装置CLと同じ駆動油圧が与えられて、油圧スイッチSWのON−OFF状態から「フェールセーフ判定」を行うことができる。 - 特許庁
The fuel shut-off valve 10 has a casing 20; a float body 41 lifted by increasing/decreasing buoyancy by a fuel liquid level in a valve chamber 30S; and the valve mechanism 44 placed on an upper part of the float 41 body and opening/closing a connection passage 32b and a spring 48 is interposed between the float body 41 and the valve mechanism 44.例文帳に追加
燃料遮断弁10は、ケーシング20と、弁室30S内の燃料液位により浮力を増減して昇降するフロート本体41と、該フロート41本体の上部に載置され、接続通路32bを開閉する弁機構44を有し、フロート本体41と弁機構44との間にはスプリング48が介在している。 - 特許庁
The nano-actuator comprises a movable member, a movable member holding structure for holding a shear piezoelectric element between the front and back surfaces of the movable member, and a control means capable of controlling the application timing of a voltage to the shear piezoelectric element arranged in such a way as to be distorted in different directions in its front and back and ON-OFF speed.例文帳に追加
ナノアクチュエータは、可動部材と、シェアピエゾ素子を前記可動部材の表裏両面から挟み込んだ可動部材保持構造と、表裏において相互に異なる方向に歪むように配した前記シェアピエゾ素子に対する電圧印加の時期とON−OFF速度をそれぞれ制御できる制御手段とを有する。 - 特許庁
Moreover, since the set value of the other side is automatically set by setting the set value of one side of either the lighting-time set value 24 or the lights-off-time set value 26 based on the first correction value 28 and the second correction value 30 preliminarily set in the storage part 22, labor for setting the set values is eliminated.例文帳に追加
また、記憶部22に予め設定された第1の補正値28と第2の補正値30に基づき、点灯時設定値24、又は消灯時設定値26のどちらか一方の設定値を設定することにより、他方の設定値が自動的に設定されるので、設定値の設定の手間が省ける。 - 特許庁
At the completion of charging and after a ball passage sensor 35 finishes checking the passage of balls and recognizes the presence of a unit number of balls, the device starts to take in game balls at the depression of a loading switch; when the output of the ball recognition sensor 55 is turned off from an on state, a process for registering loading is carried out.例文帳に追加
投入完了時に球通過センサー35での通過確認が終わりさらに球確認センサー55で単位球数の存在が確認された状態で投入スイッチが押し下げられると遊技球の取り込みを開始し、球確認センサー55の出力がONからOFFとなった時点で投入登録処理を行なう。 - 特許庁
The mobile phone is configured to include: a position acquisition means for acquiring current position information; and a memory section provided with a position information registration section for storing designated position information registered in advance by the user, and the mobile phone sets/releases the wireless unit off mode on the basis of the information registered in the position information registration section.例文帳に追加
携帯移動電話装置を、現在位置情報を取得する位置取得手段と、予めユーザが登録する、指定位置情報を記憶するための位置情報登録部を備えたメモリ部とを含み構成し、前記位置情報登録部に登録された情報に基づいて無線部オフモードの設定・解除を行うようにする。 - 特許庁
The merchandise can be displayed by being hung with a string 3 and the merchandise also can be displayed in a state where the hanging device 15 is hung on a rail or the like of the furniture by removing the tray 2 from the base plate by cutting the insertion piece 13 along the cutting-off section 14 and making the hanging device 15 be the hook by the plastic deformation.例文帳に追加
紐3で吊り下げて商品を陳列できるだけでなく、切取部14に沿って差込片13を切断することにより、トレー2を台板から取り外し、引掛具15を塑性変形させてフックとし、引掛具15を什器の横桟等に引っ掛けた状態で、商品を陳列することができる。 - 特許庁
The lithography apparatus 100 comprises a BLK deflector 212 for turning on electron beams 200 by passing them without any deflection and turning off the beams by deflecting them, a forming deflector 205 for deflecting the electron beams 200 for forming, and an objective deflector 208 for deflecting the electron beams 200 to a predetermined position in a sample 101.例文帳に追加
描画装置100は、電子ビーム200を偏向せずに通過させることでビームONさせ、偏向することでビームOFFさせるBLK偏向器212と、電子ビーム200を偏向して成形する成形偏向器205と、電子ビーム200を試料101の所定の位置に偏向する対物偏向器208と、を備える。 - 特許庁
A TR T1 is connected in parallel with the capacitor C1, and since the TR T1 is turned on/off by the rectangular wave signal, the rectangular wave signal at its positive voltage portion charges the capacitor C3 to a voltage corresponding to the time length of a half period and the rectangular wave signal at its negative voltage portion discharges the capacitor C1.例文帳に追加
このキャパシタC__1にはトランジスタT_1が並列に接続され、上記矩形波信号でオン/オフされているので、矩形波信号の正電圧の部分ではキャパシタC_1にその半周期の時間長に対応した電圧を充電させ、負電圧の部分ではキャパシタC_1の充電電荷を放電させる。 - 特許庁
A switching element 3 whose ON/OFF is performed by a desired pulse input voltage is so connected with an end of a solenoid coil 1 as to constitute a solenoid driving circuit for generating intermittently a magnetism in the solenoid coil 1, and a diode 2 for preventing the reverse current of the solenoid coil 1 is connected in series with the switching-element side of the solenoid coil 1.例文帳に追加
ソレノイドコイル1の一端に所望のパルスの入力電圧によってオンオフされるスイッチング素子3を接続し、前記ソレノイドコイル1に磁気を断続的に発生させるソレノイド駆動回路を構成し、前記ソレノイドコイル1の前記スイッチング素子側に逆流防止のダイオード2を直列に接続する。 - 特許庁
A CPU 424 subtracts ON time from OFF time of an ACC switch 19 to calculate travel time, integrates speed to calculate travel distance, and stores the calculated travel time and travel distance in a RAM 414 in association with the date and vehicle or driver.例文帳に追加
CPU424は、ACCスイッチ19のOFF時間とON時間との差をとることによって走行時間を計算するとともに、速度を積分することによって走行距離を計算し、計算した走行時間及び走行距離を日付及び車両又は乗務員と対応させてRAM414に記憶させる。 - 特許庁
Electric power control means 107 controls power to be supplied to a roller type heating element 34 in a fixing device 30, by performing the on/off control of a switching element 105 serially connected to a coil 103 for induction heating, and when abnormal voltage is detected, stops supplying the power to the heating element 34.例文帳に追加
電力制御手段107は、誘導加熱用のコイル103と直列に接続されたスイッチング素子105をオン・オフ制御することにより、定着装置30のローラ型の発熱体34への供給電力を制御するとともに、異常電圧が検出されたときは、発熱体34への電力供給を停止させる。 - 特許庁
In this refrigerating cycle device, efficiency of the entire refrigerating cycle device can be enhanced by appropriately controlling valve opening of a first flow rate control valve 109 and a second flow rate control valve 113, switching of the four-way valve 104, and ON/OFF of a first compressor 101 and a second compressor 107.例文帳に追加
第1の流量制御弁109及び第2の流量制御弁113の弁開度制御と、4方弁104の切り替え制御と、第1の圧縮機101及び第2の圧縮機107のON/OFFを最適に制御することにより、冷凍サイクル装置全体の効率を高くすることができる。 - 特許庁
Copyright © Japan Patent office. All Rights Reserved. |
※この記事は「日本法令外国語訳データベースシステム」の2010年9月現在の情報を転載しております。 |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|