意味 | 例文 (999件) |
compression ignitionの部分一致の例文一覧と使い方
該当件数 : 1188件
Mechanical compression ratio defined by stroke volume of a piston and volume of a combustion chamber 17 is set to 14 or higher, spark plugs 22 are provided to position ignition points at two or more positions separate from a center of the combustion chamber 17, and excess air ratio of air fuel mixture is set to 1.4 or higher.例文帳に追加
ピストンの行程容積と燃焼室17の容積によって決まる機械的な圧縮比を14以上に設定し、燃焼室17の中心から離れた2か所以上の位置に点火点が配置されるよう点火プラグ22を設け、かつ、混合気の空気過剰率を1.4以上に設定する。 - 特許庁
A direction of nozzle hole is set such that spray is hit on a slant face in an upstream side of the swirling flow after fuel injected from a second nozzle hole 28b in the latter half of the compression stroke is hit on a first slant face (a slant face) 42 of the top face 14, swept away by the swirling flow, and transferred around the ignition plug 6.例文帳に追加
その圧縮工程後半に第2噴口28bから噴射される燃料が頂面14の第1斜面(斜面)42に衝突した後、スワール流に流されて点火プラグ6周りに移送されるように、噴霧がスワール流の上流側の斜面に衝突するようにその噴口の向きが設定されている。 - 特許庁
The combustion control system for the compression ignition internal combustion engine capable of switching between the diffusion combustion operation mode and the premixed combustion operation mode causes the internal combustion engine to perform diffusion combustion operation if the temperature of an exhaust emission control device is lower than an activation determination temperature when the operating state of the internal combustion engine belongs to a premixed combustion operation region.例文帳に追加
本発明は、拡散燃焼運転モードと予混合燃焼運転モードを切換可能な圧縮着火式内燃機関の燃焼制御システムにおいて、内燃機関の運転状態が予混合燃焼運転領域に属する時に、排気浄化装置の温度が活性判定温度より低ければ、内燃機関を拡散燃焼運転させるようにした。 - 特許庁
The control device 1 of the engine 3, when temperature in a cylinder 3a is not less than lift-up execution cylinder temperature TENGLIFTUP after the engine 3 is subjected to idle stop, can reduce an effective compression ratio ECR and prevent the occurrence of self-ignition when restarting by controlling an intake lift LIFTIN to a lift ALCMDST_HOT for restarting at high temperature (step 9).例文帳に追加
本発明のエンジン3の制御装置1は、エンジン3がアイドルストップされた後、気筒3a内の温度がリフトアップ実施筒内温度TENGLIFTUP以上のときに、吸気リフトLIFTINを高温時再始動用リフトALCMDST_HOTに制御する(ステップ9)ことによって、有効圧縮比ECRを低下させ、再始動時における自着火の発生を防止できる。 - 特許庁
When the engine rotation speed is increasing in the compression stroke injection mode, the control device determines that the crank angle at injection end timing of the fuel injection valve deviates toward the delayed crank angle side and performs additional ignition at timing t1 when (or immediately before or after) a crank angle at actual injection end timing of the fuel injection valve of a present injection cylinder is reached.例文帳に追加
圧縮行程噴射モード中にエンジン回転速度が上昇中の場合には、燃料噴射弁の噴射終了時期のクランク角が遅角側にずれると判断して、今回の噴射気筒の燃料噴射弁の実際の噴射終了時期のクランク角に至った時点t1 (又はその直前か直後)で追加点火を実行する。 - 特許庁
In the internal combustion engine having a plurality of cylinders that can be operated in a compression ignition combustion method, a control device equipped with a means for detecting an exhaust gas temperature of each of the cylinders and an operation parameter setting means for setting an operation parameter of each of the cylinders so as to make cylinder inside temperatures of all the cylinders uniform based on the exhaust gas temperatures is provided.例文帳に追加
圧縮着火燃焼方式で運転可能な複数の気筒を有する内燃機関において、各気筒毎の排気温度を検出する手段と、前記排気温度に基づいて、全ての気筒の筒内温度が一定になるように各気筒毎に運転パラメータを設定する運転パラメータ設定手段と、を備える制御装置を提供する。 - 特許庁
To determine an upper limit quantity of an injection quantity of fuel for combustion at which excessive noise caused by HCCI (Homogeneous Charge Compression Ignition) combustion can be suppressed in a fuel injection quantity control device adopted to an internal combustion engine capable of injecting fuel for HCCI combustion and fuel for diffusion combustion at the same cycle.例文帳に追加
同一サイクルにて予混合圧縮着火(HCCI)燃焼用の燃料、及び拡散燃焼用の燃料を噴射し得る内燃機関に適用される燃料噴射量制御装置において、HCCI燃焼による騒音が過大になることが抑制され得る同燃焼用燃料噴射量の上限量を決定すること。 - 特許庁
A prereaction detecting part 5 detects prereaction of combustion at compression self-ignition combustion operation time on the basis of a detecting signal of a cylinder internal pressure sensor 18, and a fuel injection control part 6 controls a fuel injection quantity or the fuel injection timing according to prereaction time detected by the prereaction detecting part 5 to set the combustion timing as the target timing.例文帳に追加
予反応検出部5は、筒内圧力センサ18の検出信号に基づいて圧縮自己着火燃焼運転時に燃焼の予反応を検出し、予反応検出部5が検出した予反応時期に応じて燃料噴射制御部6は燃料噴射量または燃料噴射時期を制御することにより燃焼時期が目標時期となる。 - 特許庁
The control device (2) is provided with a learning part for learning the fuel property; a control part for controlling the combustion condition (compression ratio, ignition timing or the like) in a combustion chamber (CC) based on the learning result; and a feed source state detection part for detecting change of the state of a fuel feed source (161) to a fuel injector (162).例文帳に追加
本発明の制御装置(2)は、燃料性状を学習する学習部と、この学習結果に基づいて燃焼室(CC)における燃焼条件(圧縮比や点火時期等)を制御する制御部と、燃料噴射器(162)への燃料供給源(161)の状態の変更を検知する供給源状態検知部と、を備えている。 - 特許庁
This compression-ignition internal combustion engine is provided with a suction passage volume variable control means for controlling volume of a suction passage on the downstream side more than a section where an EGR device is communicated with the suction passage variably in accordance with a combustion form after switching when switching from premixed combustion to usual combustion or switching from usual combustion to premixed combustion.例文帳に追加
上記圧縮着火内燃機関において、予混合燃焼から通常燃焼への切替時又は通常燃焼から予混合燃焼への切替時に、切替後の燃焼形態に応じて、EGR装置が吸気通路に連通する部位より下流側の該吸気通路の容積を可変制御する吸気通路容積可変制御手段を更に備える。 - 特許庁
The injection control means 61 ejects fuel in the vicinity of a compression top dead center, and the intake air temperature control means 62 controls such that the temperature of intake air after mixing of exhaust gas falls in a temperature range lower than an upper limit temperature ensuring a predetermined ignition delay time and higher than a lower limit temperature avoiding the generation of HC and CO.例文帳に追加
噴射制御手段61は、圧縮上死点近傍において燃料を噴射させ、吸気温度制御手段62は、排気混合後の吸気の温度を、所定の着火遅れ時間を確保することが可能となる上限温度よりも低くかつ、HC及びCOの発生が回避される下限温度よりも高い温度範囲内となるように制御する。 - 特許庁
To further improve efficiency, in a compression ignition engine 100 where a heat accumulating member 15 for accumulating heat generated by combustion in a combustion chamber 11 and supplying heat to new air is disposed over the top of a piston 4, and the new air is compressed and fuel is self-ignited to be combusted in the combustion chamber 11.例文帳に追加
本発明は、燃焼室11における燃焼によって発生する熱を蓄熱し、新気に熱を与える蓄熱部材15を、ピストン4の頂部に渡って設け、燃焼室11において新気を圧縮し、燃料を自己着火させて燃焼させる圧縮着火エンジン100において、一層の高効率化を図ることを目的とする。 - 特許庁
The exhaust emission control device of a diesel engine 1 in which the fuel injection is executed at the timing earlier than the compression top dead center, and the ignition combustion is executed after the fuel premix is promoted includes a plasma fuel reformer 17 capable of generating reformed gas containing H_2 by the plasma discharge of the fuel F, and supplying the reformed gas in a cylinder 7 via an intake manifold 6.例文帳に追加
燃料噴射を圧縮上死点より早い時期に行い、燃料の予混合化が促進した後に着火燃焼させるようにしたディーゼルエンジン1の排気浄化装置であって、燃料Fを素にプラズマ放電によりH_2を含んだ改質ガスを生成し且つ改質ガスを吸気マニホールド6を介してシリンダ7内へ供給するプラズマ燃料改質器17を備えている。 - 特許庁
An ECU 5 as a controlling means identifies the compression stroke of the engine 1 according to the magnitude of the output fluctuation width of the generator 6 in a prescribed crank angle range determined by a reference signal 3a of a reference signal generating means comprising a projection 2a, a detecting part 3 and a waveform shaping part 4, and then outputs an ignition signal to the engine 1.例文帳に追加
このことから、制御手段としてのECU5は、突起部2a、検出部3、および波形整形部4よりなる基準信号発生手段の基準信号3aによって決定された所定のクランク角度範囲内における、発電機6の出力変動幅の大きさに基づいてエンジン1の圧縮行程時を識別し、エンジン1に対し点火信号を出力する。 - 特許庁
The DME combustion system injecting the DME fuel to an engine combustion chamber to burn the fuel includes: dividing and injecting the DME fuel; introducing an EGR gas to the combustion chamber; injecting first stage division injection before a compression top dead center; and performing second stage injection just after ignition of the DME fuel divided and injected in the first stage.例文帳に追加
DME燃料をエンジンの燃焼室に噴射して燃焼させるDME燃焼システムにおいて、噴射するDME燃料を分割して噴射すると共に、燃焼室にEGRガスを導入し、1段目の分割噴射を圧縮上死点前に噴射し、2段目の噴射を、その1段目に分割噴射されたDME燃料の着火直後に行うものである。 - 特許庁
In a predetermined partial load operation region, reduced-cylinder operation in which part of cylinders are operated is executed in an operation region D_1 on a predetermined low load side in the partial load operation region and cylinders to be operated are increased in a partial load operation region D_2 exceeding predetermined low load while executing compression self-ignition operation by increasing cylinder temperature in an operating cylinder.例文帳に追加
所定の部分負荷運転領域では、稼働気筒の筒内温度を高めて圧縮自己着火運転を実行するとともに、前記部分負荷運転領域のうち、所定の低負荷側の運転領域D_1では、一部の気筒のみを稼働させる減筒運転を実行する一方、前記所定の低負荷を越える部分負荷運転領域D_2では、稼働する気筒を増加する。 - 特許庁
To self-ignite premixed gas m in a preferable state and to realize high efficiency and low NOx in a premixed compression self-ignition engine 100 in which the premixed gas m of fuel and gas including oxygen is compressed for self-igniting and burning in a combustion chamber 11, and the reciprocating motion of a piston 2 is transmitted to a crankshaft 4 by a connecting rod to continue to rotate the crankshaft 4.例文帳に追加
本発明は、燃焼室11において、燃料と酸素含有ガスとの予混合気mを圧縮して自着火燃焼させ、ピストン2の往復運動を連結棒によってクランク軸4に伝達し、クランク軸4の回転を維持する予混合圧縮自着火エンジン100において、好ましい状態で予混合気mを自着火させ、高効率、低NOxを実現することを目的とする。 - 特許庁
The lubricating oil composition for a two-stroke cross-head marine compression-ignition (diesel) engine, is prepared by containing or mixing: (A) a major amount of a base stock having lubricating viscosity; and (B) a minor amount of an oil-soluble overbased metal detergent additive in the form of a complex wherein the basic material of the detergent is stabilized by more than one surfactant.例文帳に追加
(A)多量の、潤滑粘度を有するベースストック;及び(B)少量の、複合体形態の油溶性過塩基化金属清浄剤添加剤であって、該清浄剤の塩基性材料が1種より多くの界面活性剤により安定化されている添加剤を含む又は混合することにより製造される2ストローククロスヘッド船舶用圧縮点火(ディーゼル)エンジン用潤滑油組成物。 - 特許庁
The compression ignition internal combustion engine is provided with the tangential intake port 7 producing no swirl in the air flowed into a combustion chamber 5, and the cavity 6 depressed in a piston top face forming the combustion engine 5 and whose bottom surface is approximately flat to suppress cylinder air flow and make use of the air left at the center of the combustion chamber.例文帳に追加
圧縮着火式内燃機関において、燃焼室5内に流入される空気にスワールを生起しないタンジェンシャル吸気ポート7と、前記燃焼室5を形成するピストン頂面に凹設されその底面が略平坦な面からなるキャビティ6とを備え、筒内空気流動を抑制すると共に燃焼室中央に残存した空気の有効利用が図れるようにした。 - 特許庁
The lubricating oil composition for a 2-stroke crosshead compression ignition engine (diesel engine) for ship is composed of (A) a large amount of a base stock having a lubricating viscosity and containing or mixed with (B) a small amount of an oil-soluble overbased metal detergent additive having a composite form wherein the basic material of the detergent is stabilized with two or more surfactants.例文帳に追加
(A)多量の、潤滑粘度を有するベースストック;及び(B)少量の、複合体形態の油溶性過塩基化金属清浄剤添加剤であって、該清浄剤の塩基性材料が1種より多くの界面活性剤により安定化されている添加剤を含む又は混合することにより製造される2ストローククロスヘッド船舶用圧縮点火(ディーゼル)エンジン用潤滑油組成物。 - 特許庁
A spark trigger fuel quantity GfueltempF corresponding to the fuel quantity for generating compression ignition of fuel is calculated and a stabilized to fuel quantity GfuelDIstb corresponding to the fuel quantity contributing to torque generation of the engine is calculated, and a directly injected fuel quantity GfuelDIstb is calculated by adding the spark trigger fuel quantity GfueltempF and stabilized fuel quantity FfuelDIstb.例文帳に追加
燃料の圧縮着火を発生させるための燃料量に相当する火花トリガ燃料量GfueltempFが算出されるとともに、エンジンのトルク発生に寄与する燃料量に相当する安定化燃料量GfuelDIstbが算出され、火花トリガ燃料量GfueltempF及び安定化燃料量GfuelDIstbを加算することにより直噴燃料量GfuelDIが算出される。 - 特許庁
In the fuel injection control device 11 for a spark ignition type internal combustion engine EG including a fuel injection valve 118 which directly injects fuel to a combustion chamber, a control signal for performing a first fuel injection during from a middle period to a latter period of an intake stroke and performing a second fuel injection during from an anterior period to a middle period of a compression stroke is outputted to the fuel injection valve.例文帳に追加
燃焼室に燃料を直接噴射する燃料噴射バルブ118を備えた火花点火式内燃機関EGの燃料噴射制御装置11において、吸気行程の中期から後期の期間に第1回目の燃料噴射を行うとともに、圧縮行程の前期から中期の期間に第2回目の燃料噴射を行う制御信号を前記燃料噴射バルブへ出力する。 - 特許庁
To maximize a low temperature premixing combustion region while avoiding occurrence of premature ignition, and to sufficiently restrain generation of nitrogen oxides or soot in a diesel engine capable of burning fuel just after injection of the fuel which is injected in the vicinity of a compression top dead center by controlling an intake temperature and capable of simultaneously achieving low emission performance and improvement in fuel consumption.例文帳に追加
吸気温度のコントロールによって、圧縮上死点近傍で噴いた燃料を噴き終わって直ぐに燃やすことができ、低エミッション性と燃費向上とを同時に達成することができるようにした低温予混合燃焼を行うディーゼルエンジンにおいて、過早着火の発生を回避しつつ低温予混合燃焼領域を最大限に拡大し、NOxやすすの発生を十分に抑制できるようにする。 - 特許庁
To provide a spray shape a fuel injection valve, arrangement of a fuel injection valve, and a combustion chamber shape wherein an air layer or an air flow layer is interposed between a combustion chamber wall surface and a piston crown surface, and a fuel spray in a uniform mixture gas forming process after fuel injection, in a compression ignition type internal combustion engine for directly injecting fuel into the combustion chamber.例文帳に追加
本発明の課題は、燃焼室内に直接燃料を噴射する圧縮着火式内燃機関において、燃料噴射後の均質混合気形成過程で燃焼室壁面およびピストン冠面と燃料噴霧との間に空気層または空気流の層を介在させることのできる噴霧形状,燃料噴射弁,燃料噴射弁配置および燃焼室形状を提供することにある。 - 特許庁
To improve the volatility of fuel simultaneously with obtaining a prescribed compression ratio in a cylinder fuel injection type internal combustion engine formed with a cavity 12 recessed in the top face of a piston 11, installing an ignition plug 9 in a cylinder head 1, and installing a fuel injection valve 10, in a state in which the fuel from its jet hole 10a' in its tip part is jetted toward the cavity.例文帳に追加
ピストン11の頂面にキャビティ12を凹み形成する一方、シリンダヘッド1に、点火栓9を、装着するとともに、燃料噴射弁10を、その先端部における噴孔10a′から燃料を前記キャビティ内に向かって噴出するように装着して成る筒内燃料噴射型内燃機関において、燃料の気化性の向上と、所定の圧縮比を得ることとを同時に達成する。 - 特許庁
When a NOx occlusion amount Vns exceeds a predetermined determination amount Vc, the gear of a transmission is the third speed or higher, combustion of the internal combustion engine 2 is performing premix compression ignition combustion (PCI combustion), and the residual oxygen concentration Co is 5% or less and 1% or more in the exhaust gas G discharged from the internal combustion engine 2, a regeneration control device 10 performs NOx regeneration control.例文帳に追加
再生制御装置10が、NOx吸蔵量Vnsが所定の判定量Vcを越えた場合に、変速機のギアが3速以上であり、かつ、内燃機関2の燃焼が予混合圧縮着火燃焼(PCI燃焼)を行っており、かつ、内燃機関2から排出された排気ガスGの残留酸素濃度Coが5%以下1%以上の時に、NOx再生制御を行う。 - 特許庁
To restrain lowering of control precision caused by fluctuation of fuel pressure generated by the first injection operation of an injector to prevent worsening of a fuel comsumption, increase of emission and drive feeling, when fuel is divided into two in a compression stroke of a cylinder to be injected in a divided compressed injection area of a high load side within a stratified charge combustion range, in a spark-ignition direct injection engine.例文帳に追加
火花点火式直噴エンジン1において、成層燃焼領域の高負荷側の圧縮分割噴射領域(ロ)で、燃料を気筒2の圧縮行程で2分割して噴射させる場合に、インジェクタ12の1回目の噴射作動により発生する燃料圧力の変動に起因して制御精度が低下することを抑制し、燃費やエミッションの増大及び運転フィーリングの悪化を防止する。 - 特許庁
This compression ignition internal combustion engine performing pilot injection is provided with a piston 4, a main cavity which is a cavity provided on a crown part of the piston 4 and in which injected fuel by main injection is sucked, and a trap cavity 14b which is a cavity provided around an opening part edge part of the main cavity 14a and retains injected fuel by pilot injection under liquid or liquid-gas mixed condition.例文帳に追加
パイロット噴射を行う圧縮着火内燃機関において、ピストン4と、ピストン4の頂部に設けられたキャビティであって、主噴射による噴射燃料が吹き込まれるメインキャビティ14aと、メインキャビティ14aの開口部縁部の周辺に設けられたキャビティであって、パイロット噴射による噴射燃料を液状又は気液混合状態で保持するトラップキャビティ14bと、を備える。 - 特許庁
A fuel system for use in a combustion chamber of a compression ignition internal combustion engine comprises a pump arrangement which has a fluid pump chamber, and a piton movable from the combustion chamber to the outside to apply pressure to fluid in the pump chamber in response to pressure generated in the combustion chamber as a result of combustion, and a control valve assembly for controlling the supply of the pressure fluid in the pump chamber to an accumulator volume part.例文帳に追加
圧縮点火内燃機関の燃焼室で使用される燃料システムは、流体用ポンプ室と、燃焼の結果、燃焼室内に発生した圧力に応答してポンプ室内の流体を加圧するように燃焼室から外側に移動可能なピストンとを有するポンプ構成部を含み、ポンプ室内の加圧流体のアキュムレータ体積部への供給を制御する制御弁アセンブリをさらに含む。 - 特許庁
To achieve relatively good stratified charge combustion even when inner cylinder temperature is low by a control device for a cylinder injection spark ignition internal combustion engine that facilitates forming of a mass of combustible gas mixture inside a cavity formed on the piston top surface in the latter half of the compression process by injecting fuel inside the cavity and making inside of the cavity a stagnation space using the air intake flow turning inside the cylinder.例文帳に追加
圧縮行程後半にピストン頂面に形成されたキャビティ内へ燃料を噴射し、気筒内を旋回する吸気流を利用してキャビティ内を淀み空間とすることにより、キャビティ内に一塊の可燃混合気が形成され易くする筒内噴射式火花点火内燃機関の制御装置において、筒内温度が低い時にも比較的良好な成層燃焼を実現可能とすることである。 - 特許庁
In the control device 1 for an engine 3, HC emission HCPKM1 per unit distance discharged from a combustion chamber 3c is calculated in response to an engine speed NE and a fuel injection amount QINJ (Fig.5), and the combustion mode is switched between a diffusion combustion mode and a premixed compression ignition combustion mode in response to the calculated HC emission HCPKM1 (Steps 4, 6 of Fig.4).例文帳に追加
本発明のエンジン3の制御装置1は、エンジン回転数NEおよび燃料噴射量QINJに応じて、燃焼室3cから排出される単位距離当たりHC排出量HCPKM1を算出し(図5)、算出されたHC排出量HCPKM1に応じて、燃焼モードを拡散燃焼モードと予混合圧縮着火燃焼モードの間で切り換える(図4のステップ4,6)。 - 特許庁
To provide a premixed compression ignition engine 100 adapted to compress, self-ignite and burn mixture taken in a combustion chamber 10, which materializes an appropriate combustion state in a structure allowing simplification and miniaturization, operation in a wide output adjustment range while maintaining the appropriate combustion state, and operation control technology which enables stable startup while securing the appropriate combustion state.例文帳に追加
本発明は、燃焼室10に吸気された混合気を圧縮して自己着火燃焼させる予混合圧縮着火エンジン100において、簡単且つ小型化が可能な構成で燃焼状態を適正な状態とすることが可能、適正な燃焼状態を維持しつつ広い出力調整範囲で運転可能、更には、適正な燃焼状態を維持しつつ安定して起動可能な運転制御技術を実現することを目的とする。 - 特許庁
To suppress the occurrence of smoke and an increase of noises when the rate of residual exhaust gas increases in a compression ignition internal combustion engine A in which fuel injected and supplied into a cylinder A2 by a fuel injection valve A8 is compressed and ignited while part of the exhaust gas resides in the cylinder after combustion and the rate of the residual exhaust gas is controlled to increase/reduce depending on a load change.例文帳に追加
シリンダA2内に燃料噴射弁A8より噴射供給した燃料を圧縮して着火する一方、前記シリンダ内に燃焼後における排気ガスの一部を残留し、この残留排気ガスの比率を、負荷の変化に応じて増減制御するように構成して成る圧縮着火式内燃機関Aにおいて、前記残留排気ガスの比率を増大したときにおけるスモークの発生及び騒音の増大を低減する。 - 特許庁
To realize an operation control technology capable of simplifying structure and reducing size, bringing a combustion state to a proper state by the structure, operating in a wide output control range while maintaining the proper combustion state, and stably starting while maintaining the proper combustion state in a premixed compression ignition engine 100 in which a mixture sucked into a combustion chamber 10 is compressed, self-ignited, and burned.例文帳に追加
本発明は、燃焼室10に吸気された混合気を圧縮して自己着火燃焼させる予混合圧縮着火エンジン100において、簡単且つ小型化が可能な構成で燃焼状態を適正な状態とすることが可能、適正な燃焼状態を維持しつつ広い出力調整範囲で運転可能、更には、適正な燃焼状態を維持しつつ安定して起動可能な運転制御技術を実現することを目的とする。 - 特許庁
If low load operation in the premix combustion operation mode is continued for a first reference time or longer in the combustion control system for the compression ignition type internal combustion engine capable of changing over its operation mode between the diffusion combustion operation mode and the premix combustion operation mode, emission of white smoke is reduced by forcibly changing over the operation mode of the internal combustion engine from the premix combustion operation mode to the diffusion combustion operation mode.例文帳に追加
本発明は、拡散燃焼運転モードと予混合燃焼運転モードを切換可能な圧縮着火式内燃機関の燃焼制御システムにおいて、予混合燃焼運転モードによる低負荷運転が第1基準時間以上継続された場合に、内燃機関の運転モードを予混合燃焼運転モードから拡散燃焼運転モードへ強制的に変更することにより、白煙の排出量を低減させるようにした。 - 特許庁
To satisfactorily vaporize even fuel injected during a later half of intake stroke, and after injection, impinged and stuck to a cylinder bore in a cylinder injection type spark ignition internal combustion engine incorporating a fuel injector for injecting fuel directly into a cylinder, and performing change- over between stratified charge combustion caused by fuel injection during a later half of a compression stroke, and homogeneous change combustion caused by fuel injection during a intake stroke.例文帳に追加
直接的に気筒内へ燃料を噴射する燃料噴射弁を具備し、圧縮行程後半の燃料噴射による成層燃焼と、吸気行程の燃料噴射による均質燃焼とを機関運転状態に応じて切り換えて実施する筒内噴射式火花点火内燃機関において、吸気行程後半に噴射された燃料がシリンダボアに衝突して付着しても、この付着燃料を良好に気化させることである。 - 特許庁
This controller for the engine provided with the catalyst for burning air-fuel mixture in a combustion chamber due to compression self- ignition and purifying exhaust gas components in the combustion chamber is provided with a means for controlling the catalyst, which is provided with a means for judging an activation condition of the catalyst and a means for activating the catalyst based on the results of the judgement of the means for judging the activation condition of the catalyst.例文帳に追加
燃焼室内の混合気を圧縮自己着火により燃焼させ、前記燃焼室内の排気ガス成分を浄化する触媒を備えるエンジンの制御装置であって、該制御装置は、前記触媒を制御する手段を備え、該触媒を制御する手段は、前記触媒の活性状態を判断する手段と、該触媒の活性状態を判断する手段の判断結果に基づいて前記触媒を活性化させる手段とを備えてなる。 - 特許庁
The premixed compression ignition engine is equipped with a combustion state detecting means A for detecting the combustion state, a EGR means B allowing adjustment of emission recirculation timing to the combustion chamber while recirculating to the combustion chamber 10 the emissions emitted from the combustion chamber 10, and an operation control means C for controlling the emission recirculation timing by the EGR means B so as to make appropriate the combustion state detected by the combustion state detecting means A.例文帳に追加
燃焼状態を検出する燃焼状態検出手段Aと、燃焼室10から排出された排ガスを燃焼室10へ再循環させると共に、燃焼室10への排ガス再循環タイミングを調整可能なEGR手段Bと、燃焼状態検出手段Aで検出される燃焼状態が適正な状態となるように、EGR手段Bにより排ガス再循環タイミングを制御する運転制御手段Cとを備える。 - 特許庁
意味 | 例文 (999件) |
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|