ON- OFFの部分一致の例文一覧と使い方
該当件数 : 27736件
To provide a horizontal shaft pump (a double-suction horizontal shaft pump or self-balance multistage horizontal shaft pump) which has vane wheels disposed symmetrically, makes a radial load borne by a hydrostatic bearing, and effectively suppresses a dynamic thrust load acting on a spindle shaft in a low-flow-rate area including the vicinity of a point of cut-off.例文帳に追加
羽根車の配置が左右対称性を有し、かつ静圧軸受によりラジアル荷重を支持する構成の横軸ポンプ(両吸込横軸ポンプやセルフバランス型の多段横軸ポンプ)において、締切点付近を含む小流量領域で主軸に作用する動的スラスト荷重を効果的に抑制する - 特許庁
To solve problems that only a molded product having a thin layer can be obtained because of a subsiding phenomenon during the usable time period until a liquid synthetic resin is cured and the molded product is easy to be broken and an aggregate on the surface part is easy to be flaked off caused from deficiency in a strength because a vibration rolling is not sufficient.例文帳に追加
液状合成樹脂の硬化するまでの可使用時間帯での沈下現象のため、薄い層の成形体しかできない、また振動転圧が十分にできないため強度不足から生じる、成形体が割れ易い、表層部の骨材が剥がれ易い等の問題を解決する。 - 特許庁
This device monitors the travel state of a vehicle and surrounding environment by a radar 1 for detecting vehicle-to-vehicle distance; a G-sensor 3 for detecting deceleration; a brake on/off switch 6 for detecting brake operation; a road surface-tire friction coefficient detecting device 7; and an image detecting device by a CCD camera 9 or the like.例文帳に追加
車間距離を検出するレーダ1、減速度を検出するGセンサ3、ブレーキ操作を検出するブレーキON/OFFスイッチ6、路面−タイヤ間摩擦係数検出装置7、CCDカメラ9等による画像検出装置などによって、車両の走行状態や周囲の環境を監視する。 - 特許庁
To provide a joint fitting which enables a butt end surface of a horizontal wood member to be safely, easily and temporarily joined to a side surface of the horizontal wood member on a construction site, and which enables the butt end surface of the horizontal wood member to be firmly joined so as not to come off upward, after temporary joining.例文帳に追加
施工現場において、横木部材の木口面を横木部材の側面に安全かつ容易に仮接合でき、かつ、仮接合させた後、横木部材の木口面が上方に抜けないように強固に接合することの可能な接合金具の提供を目的とする。 - 特許庁
On the other hand, when the motor body 2 is not driven, the clutch 24 disconnects the warm shaft 22 from the rotary shaft 10 to cut off the rotary shaft 10 being a rotary load of the output shaft 23a from a load side from the warm shaft 22, and enables an easy manual operation of the slide door.例文帳に追加
一方、モータ本体2の非駆動時においては、クラッチ24は、ウォーム軸22と回転軸10とを断絶して負荷側からの出力軸23aの回転負荷になる回転軸10をウォーム軸22から切り離し、手動によるスライドドアの容易な開閉作動を可能とする。 - 特許庁
When the main body housings are closed and the magnet 18 and the switch 19 are close to each other, the switch 19 is turned ON, and when the main body housings are opened and the magnet 18 and the switch 19 are separated, the switch 19 is turned OFF so as to detect the opened/closed states of the main body housings.例文帳に追加
本体筐体が閉じて磁石18とリードスイッチ19が接近しているときはリードスイッチ19がONになり、本体筐体が開いて磁石18とリードスイッチ19が離れたときはリードスイッチ19がOFFになるようにして、本体筐体の開閉状態を検出するようにしている。 - 特許庁
When a state change (from OFF to ON) from a point stored in a fire determination point storage part of a main control section 1 is transmitted from a terminal device 6 to the main control section 1 of a centralized monitoring device, the mode switching means of the main control section 1 transmits a fire mode switching notice to an arithmetic unit 3.例文帳に追加
端末装置6から集中監視装置の主制御部1へ主制御部1の火災判断ポイント記憶部に記憶されたポイントから状態変化(オフからオン)が送信されたとき、主制御部1のモード切替手段は演算装置3に対し火災モード切替通知を送信する。 - 特許庁
The second drive control means 120 generates a drive signal which falls at a third speed V_3, when the signal rises in such a direction as to turn on the first switch means 10 and rises at a fourth speed V_4, when the signal falls in such a direction as to turn off the first switch means 10.例文帳に追加
第2駆動制御手段120は、第1スイッチ手段10をオンさせる方向の立ち上がり時には第3速度V_3で立ち下げ、第1スイッチ手段10をオフさせる方向の立ち下がり時には、第4速度V_4で立ち上げる駆動信号を発生する。 - 特許庁
When the second contact 4 lying at the on-position is relatively separated from the first contact, the second contact 4 is connected to the first contact 3 through the resistor 6, and when the second contact 4 is moved at the off-position, the second contact 4 shuts down the current while making the first contact not contact with the resistor 6.例文帳に追加
オン位置にある第2接点4と第1接点3とが相対的に離れるとき、第2接点4が抵抗体6を介して第1接点3に接続され、第2接点4がオフ位置に移動すると、第1接点3と抵抗体6に接触しないようにして電流を遮断する。 - 特許庁
The threshed stems are carried to a treatment chamber 19 from a stem discharge port 33 formed on the back wall 32 of the threshing chamber 15 and stuck grains remaining in the stems in the treatment chamber 19 are scraped off while they are transferred to a discharge chain 35 in the treatment chamber 19 and conveyed to a discharged stem cutter.例文帳に追加
脱穀された稈は、前記扱ぎ室15の後壁32に形成された排稈口33から処理室19へ搬入され、前記処理室19内で排稈チェーン35に受け渡され排稈切断装置へ搬送される間に前記処理室19内で稈に残る刺さり粒が掻き落とされる。 - 特許庁
To provide a mounting structure of an eaves gutter supporting implement capable of fixing a mounting base on a mounting face without allowing it to rotate together with a screw, come off, and float by applying agent for improving screw fixation made of functional resin being different from base resin into an insertion hole provided in the mounting base.例文帳に追加
ベース樹脂とは異なる機能性樹脂からなるビス固定性向上剤を取付け基台に穿った挿通孔に複合させ、ビスと共に回ることなく、外れたり、浮いたりすることなく該取付け基台を被取付面に固定することのできる軒樋支持具の取付構造を提供する。 - 特許庁
To appropriately prevent peel-off at a conductive adhesive material connection part in a mounting structure, in which a capacitor is loaded through a conductive adhesive material on one surface of both lead frames, in a state of crossing over a pair of the lead frames facing each other at a distant.例文帳に追加
離間して対向する一対のリードフレームの間を跨いで横断した状態で両リードフレームの一面に導電性接着剤を介してコンデンサを搭載した実装構造において、導電性接着剤接続部における剥離の発生を適切に防止できるようにする。 - 特許庁
When a bundle of documents on the document tray is detected by a set switch 603 and an upper limit switch 311 for detecting that the elevating plate is at a proper conveyance position is off, a driving amount setting part 602 sets amount of driving of a lift motor 503 to a prescribed amount of driving.例文帳に追加
セットスイッチ603により原稿トレイ上の原稿束が検出された際に、昇降板が搬送適正位置であることを検出する上限スイッチ311がオフ状態である場合、駆動量設定部602はリフトモータ503の駆動量を規定駆動量に設定する。 - 特許庁
Therefore, if pulse drive signals of a secondary-side semiconductor switch element 32 are sent out in accordance with the turn- on and-off of the main switching element 6, the output circuit 15 can be extremely reduced in size while the constitution is simple wherein a full-wave rectifying circuit is merely adopted as the rectifying circuit 18.例文帳に追加
したがって、二次側半導体スイッチ素子32のパルス駆動信号を、主スイッチング素子6のオンおよびオフにそれぞれ合わせて送り出すようにすれば、整流回路18を全波整流回路にしただけの簡単な構成でありながら、出力回路15を極端に小型化できる。 - 特許庁
This device comprises a temperature rise control part 15 for processing input present speed and pressure as predetermined and outputting a first switch instruction and a switch part 16 to be controlled by the first switch instruction for controlling the ON/OFF of a power supply to a fan motor 7a.例文帳に追加
現在速度および現在圧力を入力として所定の処理を行って第1のスイッチ指令を出力する昇温制御部15と、第1のスイッチ指令により制御されてファンモータ7aへの供給電源のON/OFFを制御するスイッチ部16とを有している。 - 特許庁
To provide a car-mounted control device for a vehicle equipped with a notifying means to make notification about the condition of a turn lamp being put on or off using an indicator, a buzzer sounding, etc. capable of suppressing effectively the variation of in the lighting period of the indicator and variation in the sounding period of the buzzer etc.例文帳に追加
ターンランプの点灯または消灯の状態をインジケータおよびブザー等の鳴動によって通知する通知手段を備えた車両において、インジケータの点灯周期変動およびブザー等の鳴動周期変動を効果的に抑えることができる車載制御装置を提供する。 - 特許庁
A switch element 40 is changed over between ON state and OFF state by the output of a control circuit 39, and by switching the current of the constant-current sources 35, 36, the current of a prescribed frequency is generated completely, and the current of the prescribed frequency is sent into a wiring path where a transmitter is connected.例文帳に追加
スイッチング素子40は制御回路39の出力によってオンオフされ、定電流源35,36の電流をスイッチングして所定周波数の電流を完結的に発生させて、所定周波数の電流を送信器20が接続された配線路に流す。 - 特許庁
The molded component takeoff device 5 comprises: a board 7 extended from a take off device body 6 and inserted as an insertion section into a mold 2 in which mold opening is carried out; and a couple of secure pins 8 extended so as to project toward each brush holder 3 left and put on a mold 2a from this board 7.例文帳に追加
成形品取り出し装置5は、取り出し装置本体6から延設されて、型開きされた金型2内に挿入される挿入部としてのボード7と、該ボード7から金型2aに残し置かれた各ブラシホルダ3に向かって突出するように延設された一対の保持ピン8とを備える。 - 特許庁
Articles W dropped off a hopper 24 of this article aligning and conveying apparatus are distributed to the right and left in the conveying direction D1 on article aligning and conveying boards 11 by the oscillating action of an oscillating cage and stored in respective channels 11a of the article aligning and conveying boards 11.例文帳に追加
物品供給装置のホッパ24から落下した物品Wは、揺動かごの揺動作用により物品整送板11上で搬送方向D1の左右両側に振り分けられ、物品整送板11上の各溝11a内に物品Wが収容される。 - 特許庁
To solve the problem wherein a safety device 31, which compulsorily closes an on-off valve for supplying gas to a burner, if a microcomputer for performing combustion control is in an abnormal condition, does not operate unless abnormality occurs in the microcomputer 1, and therefore even if the safety circuit 31 is out of order, an ignition operation is performed as it is.例文帳に追加
燃焼制御を行うマイコンが異常の場合に、バーナへガスを供給する開閉弁を強制的に閉弁させる安全装置31は、マイコン1に異常が生じないと作動しないので、安全回路31が故障していてもそのまま点火操作が行われる。 - 特許庁
To improve the suitability of an emulsion layer (gelatin) washing off at washing in the production of an aluminum planographic printing plate utilizing a silver complex salt diffusion transfer process and to produce an aluminum planographic printing plate excellent in ink receptivity and printing durability while preventing the sticking of a deposit on a roller in a processing apparatus.例文帳に追加
銀錯塩拡散転写法を利用したアルミニウム平版印刷版の製版処理において、水洗処理時の乳剤層(ゼラチン)のウォッシュ・オフ性を向上させ、インキ受理性及び耐刷力に優れたアルミニウム平版印刷版の製版方法を提供することにある。 - 特許庁
When a gate voltage voltage Vge exceeds the boundary voltage value Vbor, since the 1st switching transistor Tr1 is turned on and the 2nd switching transistor Tr2 is turned off, the base voltage of the gate control transistor Tr3 becomes equal to the voltage drop amount corresponding to those of current detection resistor R1 and R2.例文帳に追加
一方、ゲート電圧Vgeが境界値Vbor を超えたときは、第一切替トランジスタTr1がオンすると共に第二切替トランジスタTr2がオフするため、ゲート制御トランジスタTr3のベース電圧は2つの電流検出抵抗R1,R2による電圧降下分となる。 - 特許庁
The frequency converter comprises an LC resonance circuit 1 resonating with a predetermined variable resonance frequency, a differential circuit 2 where CMOS transistors M_P and M_N are turned on/off alternately, and a control current generating circuit 3 provided with a CMOS transistor M_B for controlling the current supply to the differential circuit 2.例文帳に追加
周波数コンバータは、可変な所定共振周波数で共振するLC共振回路1と、CMOSトランジスタM_P ,M_N が交互にオン・オフする差動回路2と、該差動回路2に供給する電流を制御するCMOSトランジスタM_B を備えた制御電流生成回路3とを備える。 - 特許庁
On the surfaces of the piezoelectric substrate 50, dummy electrodes 52a and 52b (the number of dummy electrodes is an example) are arranged along a cutting line along which the substrate 50 is cut off from the wafer (in other words, along the border line of the substrate 50) in addition to a pair of electrodes 51a and 51b for input or output.例文帳に追加
圧電体基板50の表面には、入力用又は出力用の一対の電極51a、51bに加えて、ウエハから基板50を切り出す際のカット線(言い替えれば基板50の輪郭線)に沿ってダミーの電極(個数は一例)52a、52bを設ける。 - 特許庁
A switch SW3 of a connecting circuit 504 is connected between a signal line L2, branched from an input terminal T1 of a pilot signal CPLT in a charging inlet 270, and a grounding line L3 connected to a vehicle ground 518 while being turned on/off according to a control signal from a CPU 512.例文帳に追加
接続回路504のスイッチSW3は、充電インレット270におけるパイロット信号CPLTの入力端子T1から分岐された信号線L2と、車両アース518に接続される接地線L3との間に接続され、CPU512からの制御信号に応じてオン/オフされる。 - 特許庁
At this time, the clutch 8 is cut off and it is displayed on a display means 27 by judging it as a failure when detected pressure at a pressure detection means 17 exceeds second standard pressure Ps2 before set time Ts passes after it exceeds first standard pressure Ps1.例文帳に追加
このとき、圧力検出手段17での検出圧力が第1基準圧力Ps1を越えてから、設定時間Ts経過する前に第2基準圧力Ps2を越えることにより故障していると判断し、クラッチ8を遮断すると共に、その旨を表示手段27に表示させる。 - 特許庁
The device is provided with the radio tag 6 consisting of an antenna 3 receiving radio wave, a radio tag IC 4 receiving supply of a power source by receiving the radio wave and sending data from the antenna 3 with the use of the power source, and a switch 5 controlling transmission of the data of the radio tag IC 4 with an ON/OFF control.例文帳に追加
無線電波を受信するアンテナ3と、無線電波を受信して電源の供給を受け、この電源を利用してデータをアンテナ3から送信する無線タグIC4と、当該無線タグIC4のデータの送信をON/OFF制御するスイッチ5とから成る無線タグ6を有している。 - 特許庁
To provide a gate drive circuit that adjusts a dead time in the gate drive circuit even if the dead time is not set in a gate signal control circuit, and sets a value of the dead time to a proper value even if turn-off/turn-on characteristics are changed, thereby improving the efficiency of power supply.例文帳に追加
ゲート信号制御回路内で設定しないでもデッドタイムをゲートドライブ回路内で調整でき、デッドタイムの値をターンオフ、ターンオンの特性が変化した場合にも適正な値とすることができ、電源効率を向上させることのできるゲートドライブ回路を提供する。 - 特許庁
The control section CONT detects the voltage between an application power voltage of the battery B and the chassis terminal (unit ground terminal) and generates a switch drive signal for applying on-control to the switch circuit SW when the voltage is proper and applying off-control to the switch circuit SW when discriminating that a grounding fault takes place.例文帳に追加
制御部CONTは、バッテリBの印加電源電圧とシャシ端子(ユニット接地端子)との間の電圧を検出すると共に、該検出に基づいて適正と判定されたときにスイッチ回路SWをオン制御し、地絡と判定されたときにオフ制御するスイッチ駆動信号を生成する。 - 特許庁
When a mobile phone 2 is loaded on the charging apparatus 1 when a switch 16 is turned off, a control section 12 reads data from a memory 23 of the mobile phone 2 and once stores the data to a sub memory 14 and thereafter stores the data to a main memory 13 in reference with a telephone number of the mobile phone 2.例文帳に追加
スイッチ16がオフの場合に、携帯電話機2を充電装置1に装着すると、制御部12は携帯電話機2のメモリ23からデータを読み出してサブメモリ14に一旦保持した後、携帯電話機2の電話番号に関連付けてメインメモリ13に記憶する。 - 特許庁
To reduce the quantity of a refrigerant by opening first and second on/off valves at the time of cold storage operation and closing any one of them at the time of utilization cooling operation thereby halving the size of a supercooler and enhancing the thermal storage capacity.例文帳に追加
蓄熱能力を向上させ、かつ、蓄冷運転時と利用冷房運転時の必要冷媒量の差を小さくし、冷媒封入量の増加を抑えることのできる蓄熱ユニット及び該蓄熱ユニットを組込んだ空気調和装置の運転方法を提供することにある。 - 特許庁
Accordingly, this device is arranged, so that the switch can be switched to the side a by changeover switch 23, until a specified time passes after the FET 16 is turned on, and this validates the PWM signal, regardless of the output signal of the comparator 22, and inhibits the compulsive turning off of the FET 16.例文帳に追加
したがって、FET16がオンとなってから所定時間が経過するまでは、切り替えスイッチ23によってスイッチがa側へ切り替えられるようにし、コンパレータ22の出力信号に関係なくPWM信号を有効として、FET16の強制的なオフを禁止する。 - 特許庁
The working pulses comprise eroding pulses for eroding material off the workpiece and measuring pulses, and during measuring pulses, an ignition voltage Uing is applied on the work gap 4 in order to initiate a discharge within the work gap and to measure the corresponding ignition delay time TD.例文帳に追加
加工パルスは、被加工物から材料を侵食するための侵食パルスと、測定パルスとを含み、該測定パルスの間、イグニション電圧(Uing)が、加工ギャップの中で放電を開始しかつ対応するイグニション遅延時間(TD)を測定するために、加工ギャップ(4)に印加される。 - 特許庁
A control circuit 18 can put a load 13 in long-time timer operation by the operation switch SW_0 that the electronic timer switch 15 itself has and also put the load 13 in short-time delay timer operation by the signal of a sensor circuit 16 detecting the external mechanical switch SW_1 being ON or OFF.例文帳に追加
制御回路18は、電子タイマースイッチ15自身が有する操作スイッチSW0によって、負荷13を長時間タイマー動作させると共に、外付けの機械スイッチSW1のオン,オフ状態を検出するセンサー回路16の信号により、負荷13を短時間型遅動タイマー動作させることが可能である。 - 特許庁
Consequently the gap S formed between the LCD panel 1 and the circuit substrate 3 is closed off with the dust proof sheet 8 and invasion of foreign matters made of metal and so on into the connection part B of the LCD panel terminal 4 of the LCD panel 1 and the TAB output terminal 5 of the TAB 2 is prevented.例文帳に追加
したがってLCDパネル1と回路基板3の間に形成される隙間Sは防塵シート8で閉塞され、LCDパネル1のLCDパネル端子4とTAB2のTAB出力端子5の接続部分Bに金属製異物等が混入するのが阻止される。 - 特許庁
This governor mechanism 8 for the elevator comprises a speed detection part 10 installed between a car and an operating part 14 installed on a car 1 and cutting off the power supply of the drive device 1b or operating the emergency stop device 82 when the speed of the car 1 exceeds a specified value.例文帳に追加
エレベータ用調速機構8は、乗りかご1に設置され乗りかご1の速度が一定値を越えた場合に駆動装置1bの電源を切るか、または非常止め装置82を作動させる動作部14との間に介在された速度検出部10とを備えている。 - 特許庁
To provide a wireless apparatus which suppresses wasteful power consumption while maintaining a stable apparatus state and easily performing power ON/OFF operation of the apparatus and operation start/stop operation or the like with excellent user-friendliness, and also to provide a power supply management method of the wireless apparatus.例文帳に追加
本発明は、安定した機器状態を維持しつつ無駄な電力消費を抑制できるとともに、機器の電源オン/オフ操作、動作の開始/停止操作等が容易に行える使い勝手のよい無線機器および無線機器の電源管理方法を提供することを課題とする。 - 特許庁
Based on the position signal from which a frequency component lower than predetermined cut-off frequency in accordance with the exposure time is removed, the imaging device 20 is moved along the plane perpendicular to the optical axis of the photographic lens 16 by a camera shake correction mechanism 80, and image blur caused by the camera shake is prevented.例文帳に追加
露光時間に応じた所定のカットオフ周波数よりも低い周波数成分が除かれた位置信号に基づいて、手ぶれ補正機構80により、撮像素子20が撮影レンズ16の光軸に垂直な面に沿って移動され、手ぶれによる像ぶれが防止される。 - 特許庁
A metal film (a light shut off film) made of chromium, silver, aluminum or the like is formed in a region joined to the cap and the vicinity of the region on the surface of the insulating base plate 51, and a mesh- like metal film 54 is fomred in the central part (an infrared incoming region) of the surface.例文帳に追加
そして前記絶縁基板51の表面には前記キャップと接合する領域とその近傍にクロム、銀、アルミニウム等からなる金属膜(光線遮断膜)53を形成し、また同表面の中央部分(赤外線入射領域)にはメッシュ状の金属膜54が形成されている。 - 特許庁
The lubricating oil leaked from the reduction gear 20 and stuck on an outer periphery of a rotary shaft 9 is scraped off by a brush 52 of an oil scraping means 50, and the lubricating oil is discharged from predetermined discharging passage after the scraped oil is temporarily stored inside a body 51 of the oil scraping means 50.例文帳に追加
また、減速機20から漏出して回転軸9の外周面に付着した潤滑油を油落とし手段50のブラシ52により擦り落とすとともに、その本体部分51の内部に一時的に収納した後、所定の排出経路を通して排出する。 - 特許庁
To provide a stacked secondary battery reducing coming off of an active material from a positive electrode and a negative electrode and mixing of it to them, preventing failure of self discharge and short circuit, and facilitate the sure arrangement of a positive active material layer on the inside of a negative active material layer.例文帳に追加
正極、負極からの活物質の脱落及び対極への混入の低減を図り、自己放電及び短絡の不良を生じさせず、かつ正極活物質層が必ず負極の活物質層の内側に配置されていることを容易にする積層型二次電池を提供する。 - 特許庁
When connection of a card unit 15 and a delivery control board 60 is disconnected and on of VL cannot be detected, a delivery control part 61 inhibits lending control and turns a card unit connection signal off to inform disconnection with the card unit 100 to a game control part 41.例文帳に追加
カードユニット15と払出制御基板60との接続が断絶し、VLのonを検出できなくなると、払出制御部61は、貸出制御を禁止するとともに、カードユニット接続中信号をoffとしてカードユニット100と接続されていない旨を遊技制御部41に対して通知する。 - 特許庁
The slipping and falling down can be prevented even if getting off the balance and staggering when standing on one foot for wiping the other foot because the laying face of the mat body is the mesh-shaped net for preventing the slipping and the mesh-shaped net for preventing the slipping adheres to the floor, or the like.例文帳に追加
又、マット本体の敷設面は滑り止め用の網状ネットであるため、一方の足を拭くために、もう一方の足だけで立っていてバランスをくずしてふらついても、滑り止め用の網状ネットが床などに密着しているため、滑ったりこけたりするのを防ぐ事ができる。 - 特許庁
In this method, a reaction of raw material in a nozzle SP is suppressed by setting the nozzle SP hard to receive an effect of a convective heat transferred in vertical direction from the substrate 22 under heating due to locating the nozzle SP on an off-position of a vertical upward area R of the substrate 22.例文帳に追加
本方法においては、噴出口SPを基板22の鉛直上方領域Rから外れた位置に配置することで、加熱中の基板22から鉛直方向に伝搬する対流熱の影響を受け難くし、噴出口SP内での原料の反応を抑制することとした。 - 特許庁
An image signal, i.e., DATA, is subjected to pixel modulation at a modulating section 78 and a logic element 70 turns a switch 79 on/off by ORing the output signal from the modulating section 78 and a full lighting signal FULL from a sequence controller 77 thus controlling the pulse current of a laser 73A.例文帳に追加
画像信号であるDATAは、変調部78において画素変調され、その出力信号とシーケンスコントローラ77からのフル点灯信号FULLのORを出力する論理素子70によりON/OFFするスイッチ79によって、レーザ73Aのパルス電流は制御される。 - 特許庁
The wireless tag 2 is constituted of an antenna 3 for receiving a radio wave, a wireless tag IC 4 for receiving supply from a power source by receiving the radio wave, and transmitting data from the antenna 3 by utilizing the power source, and a switch 5 for performing ON/OFF control of data transmission by the wireless tag IC 4.例文帳に追加
そして、前記無線タグ2を、無線電波を受信するアンテナ3と、無線電波を受信して電源の供給を受け、この電源を利用してデータをアンテナ3から送信する無線タグIC4と、当該無線タグIC4のデータの送信をON/OFF制御するスイッチ5とで構成している。 - 特許庁
To provide a cutting device capable of preventing a contamination sticking to an outer peripheral part of a cutting blade from sticking to a surface of a workpiece by rotating once together with the cutting blade, by cutting off a turning flow of a cutting liquid including the contamination on the outer periphery of the cutting blade.例文帳に追加
切削ブレードの外周上におけるコンタミを含んだ切削液の回流を遮断することにより,切削ブレードの外周部に付着したコンタミが切削ブレードと共に1回転して被加工物の表面に付着することを防止することが可能な切削装置を提供する。 - 特許庁
A plurality of cutting long sections 2 are provided on the film sheet 1, and in addition, the film sheet 1 is cut off by the plurality of cutting long sections 2 whereby the approximately strip-like tear region which is wider than a width of the sections 2 can be formed.例文帳に追加
フィルムシート1に複数の切断用長状体2が設けられ、且つ該複数の切断用長状体2により該フィルムシート1を切り取ることで該切断用長状体2の幅より幅広な略帯状開裂部位を形成可能な構成にしてなることを特徴とする。 - 特許庁
To prevent occurrence of pressure losses, noises, and vibrations caused by peeling-off and vortex in a flow at a bending part of a large bending structure, wherein the flow from an exterior piping to a manifold or from a stack to the manifold is bent in a large curve on its half way from entrance part of the manifold to exit side.例文帳に追加
外部配管からマニフォールドへの流れ、またはスタックからマニフォールドへの流れを、マニフォールドの入口部から出口側へと向かう途中で大きく曲げる構造では、当該屈曲部にて流体が剥離や渦を生じるため圧力損失および騒音、振動が発生する。 - 特許庁
Meanwhile, a control status, for instance, whether a digital signal T-101D made to correspond to an alarm, etc., is ON or not is discriminated (ST4), and the temporarily stored collection data are thinned every 200 millisecond during OFF (ST5), recorded in a data storing part and also subjected to trend display (ST6 and ST7).例文帳に追加
一方、制御スティタス、例えば警報等に関連付けたデジタル信号T−101DがONか否かを判定し(ST4)、OFFの間は1秒毎(ST5)に、200ミリ秒毎に一時記憶した収集データを間引いて、データ格納部に記録するとともに、トレンド表示する(ST6、ST7)。 - 特許庁
Copyright © Japan Patent office. All Rights Reserved. |
ログイン |
Weblio会員(無料)になると
|
ログイン |
Weblio会員(無料)になると
|